Operation CHARM: Car repair manuals for everyone.
Home >> Acura Truck >> 2001 >> MDX V6-3471cc 3.5L >> Repair and Diagnosis >> Powertrain Management >> Computers and Control Systems >> Testing and Inspection >> Initial Inspection and Diagnostic Overview >> Diagnostic Strategies

Diagnostic Strategies

General Troubleshooting Information

Intermittent Failures
The term "intermittent failure" means a system may have had a failure, but it checks OK now. If the Malfunction Indicator Lamp (MIL) on the dash does not come on, check for poor connections or loose wires at all connectors related to the circuit that you are troubleshooting.

Opens and Shorts
"Open" and "Short" are common electrical terms. An open is a break in a wire or at a connection. A short is an accidental connection of a wire to ground or to another wire. In simple electronics, this usually means something won't work at all. In complex electronics (like PCM's) this can sometimes mean something works, but not the way it's supposed to.

How to Use the PGM Tester or a Scan Tool

If the MIL (Malfunction Indicator Lamp) has come on




1. Start the engine and check the MIL.

NOTE: If the ignition switch is turned ON (II), and the engine is not started, the MIL will stay on for 15 - 20 seconds.




2. If the MIL stays on, connect the Honda PGM Tester (A) or an OBD II scan tool to the Data Link Connector (DLC) (B) located behind driver's dashboard lower cover.
3. Turn the ignition switch ON (II).
4. Check the Diagnostic Trouble Code (DTC) and note it. Also check the freeze frame data. Refer to the DTC Troubleshooting Index and begin the appropriate troubleshooting procedure.

NOTE:
- Freeze frame data indicates the engine conditions when the first malfunction, misfire or fuel trim malfunction was detected.
- The scan tool and the Honda PGM Tester can read the DTC, freeze frame data, current data, and other Powertrain Control Module (PCM) data.
- For specific operations, refer to the user's manual that came with the scan tool or Honda PGM Tester.

If the MIL did not come on
If the MIL did not come on, but there is a driveability problem, refer to the Symptom Troubleshooting Index .

If you can't duplicate the DTC
Some of the troubleshooting requires you to reset the PCM and try to duplicate the DTC. If the problem is intermittent and you can't duplicate the code, do not continue through the procedure. To do so will only result in confusion and, possibly, a needlessly replaced PCM.

How to Reset the PCM
You can reset the PCM in either of 2 ways:
- Use the OBD II scan tool or Honda PGM Tester to clear the PCM's memory.
See the OBD II scan tool or Honda PGM Tester user's manuals for specific instructions.




- Turn the ignition switch OFF, and remove the No. 13 CLOCK BACKUP fuse (7.5 A) (A) from the passenger's under-dash fuse/relay box (B) for 10 seconds.

How to End a Troubleshooting Session (required after any troubleshooting)
1. Reset the PCM as described above.
2. Turn the ignition switch OFF.
3. Disconnect the OBD II scan tool or Honda PGM Tester from the DLC.

NOTE: The PCM is part of the immobilizer system. If you replace the PCM, it will have a different immobilizer code. In order for the engine to start, you must rewrite the immobilizer code with the Honda PGM Tester.

How to Remove the PCM for Testing
If the inspection for a trouble code requires voltage or resistance checks at the PCM connectors, remove the PCM and test it:




1. Remove the passenger's center console side trim (A).
2. Remove the bolt from the intake manifold runner control (IMRC) module (B).
3. Remove the two nuts from the bracket (C).




4. Remove the bolt and the nut from the PCM.

How to Troubleshoot Circuits at the PCM

Special Tools Required
- Digital Multimeter KS-AHM-32-003 (1) or a commercially available digital multimeter
- Backprobe Set 07SAZ-001000A (2)




1. Connect the backprobe adapters (A) to the stacking patch cords (B), and connect the cords to a digital multimeter (C).
2. Using the wire insulation as a guide for the contoured tip of the backprobe adapter, gently slide the tip into the connector from the wire side until it touches the end of the wire terminal.
3. If you cannot get to the wire side of the connector or the wire side is sealed (A), disconnect the connector and probe the terminals (B) from the terminal side. Do not force the probe into the connector.






NOTE: Do not puncture the insulation on a wire.Punctures can cause poor or intermittent electrical connections.

How to substitute the PCM for Testing Purposes

Use this procedure if you need a known-good PCM to test a vehicle. It allows you to swap a PCM from a "donor" vehicle without having to program it to the test vehicle's ignition key.

1. Cut a temporary ignition key for the test vehicle with a non-immobilizer key blank.
2. Remove the PCM from the test vehicle.
3. Write the test vehicle's VIN on the PCM you just removed to avoid confusing it with the donor vehicle's PCM.
4. Remove the known-good PCM from the donor vehicle, and install it in the test vehicle.




5. Tape the donor vehicle's ignition key head-to-head to the test vehicle's temporary key (A). The PCM will recognize the code from the donor vehicle's key (B) and allow you to start the engine with the temporary key.
6. After completing your tests, reinstall both PCMs, and destroy the temporary key.
pro multis · About Operation CHARM