Automatic Transmission
DTC P0873: Open in 4th Clutch Transmission Fluid Pressure Switch Circuit, or 4th Clutch Transmission Fluid Pressure Switch Stuck OFFNOTE:
^ Before you troubleshoot, record all freeze data and any on-board snapshot, and review General Troubleshooting Information.
^ This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
1. Clear the DTC with the HDS.
2. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
3. Test-drive the vehicle in 4th gear in the sequential sportshift mode in S, and verify with the HDS in the A/T data list that the SHIFT COMMAND indicates 4th.
4. Check the 4th PRESSURE SWITCH signal with the HDS in the A/T data list.
Is the 4th PRESSURE SWITCH ON?
YES - Go to step 5.
NO - Go to step 7.
5. Test-drive the vehicle in 4th gear in the sequential sportshift mode in S for at least 2 seconds, then slow down and stop the wheels.
6. Monitor the OBD STATUS for P0873 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate FAILED?
YES - Go to step 7.
NO - Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the 4th clutch transmission fluid pressure switch and the PCM. If the HDS indicates NOT COMPLETED, return to step 5 and recheck.
7. Turn the ignition switch to LOCK (0).
8. Disconnect the 4th clutch transmission fluid pressure switch connector.
9. Turn the ignition switch to ON (II).
10. Measure the voltage between the 4th clutch transmission fluid pressure switch connector terminal and body ground.
Is there about 5 V?
YES - Replace the 4th clutch transmission fluid pressure switch, then go to step 20.
NO - Go to step 11.
11. Turn the ignition switch to LOCK (0).
12. Jump the SCS line with the HDS.
13. Disconnect PCM connector C (44P).
14. Check for continuity between PCM connector terminal C38 and the 4th clutch transmission fluid pressure switch connector terminal.
Is there continuity?
YES - Check for poor connections and loose terminals at the 4th clutch transmission fluid pressure switch and the PCM. If the connections are OK, go to step 15.
NO - Repair open in the wire between PCM connector terminal C38 and the 4th clutch transmission fluid pressure switch, then go to step 20.
15. Reconnect all connectors.
16. Update the A/T software in the PCM if it does not have the latest software, or substitute a known-good PCM.
17. Test-drive the vehicle in 4th gear in the sequential sportshift mode in S for at least 2 seconds, then upshift to 5th gear, and drive in 5th gear for at least 2 seconds. Slow down and stop the wheels.
18. Check for DTC(s) in the DTCs/Freeze Data in A/T Mode Menu with the HDS.
Is DTC P0873 indicated?
YES - If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to step 1.
NO - Go to step 19.
19. Monitor the OBD STATUS for P0873 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate PASSED?
YES - If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM. If any other DTCs were indicated on step 18, go to the indicated DTC's troubleshooting.
NO - Check for poor connections and loose terminals at the 4th clutch transmission fluid pressure switch and the PCM. If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, return to step 17 and recheck.
20. Reconnect all connectors.
21. Clear the DTC with the HDS.
22. Test-drive the vehicle in 4th gear in the sequential sportshift mode in S for at least 2 seconds, then upshift to 5th gear, and drive in 5th gear for at least 2 seconds. Slow down and stop the wheels.
23. Check for DTC(s) in the DTCs/Freeze Data in A/T Mode Menu with the HDS.
Is DTC P0873 indicated?
YES - Check for poor connections and loose terminals at the 4th clutch transmission fluid pressure switch and the PCM, then go to step 1.
NO - Go to step 24.
24. Monitor the OBD STATUS for P0873 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate PASSED?
YES - Troubleshooting is complete. If any other DTCs were indicated on step 23, go to the indicated DTC's troubleshooting.
NO - Check for poor connections and loose terminals at the 4th clutch transmission fluid pressure switch and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, return to step 22 and recheck.