A/T Clutch Pressure Control Solenoid Valve B Test
A/T Clutch Pressure Control Solenoid Valve B Test
1. Connect the HDS to the DLC (A).
2. Select Clutch Pressure Control (Linear) Solenoid B in the Miscellaneous Test Menu on the HDS.
NOTE: If the HDS does not communicate with the PCM, troubleshoot the DLC circuit. Testing and Inspection
3. Test A/T clutch pressure control solenoid valve B with the HDS.
- If the valve tests OK, the test is complete. Disconnect the HDS.
- If the valve does not test OK, follow the instructions on the HDS.
- If the valve does not test OK, and the HDS does not determine the cause, go to step 4.
4. Do the battery removal procedure. Removal and Replacement
5. Remove the charge air cooler cover.
6. Remove the air cleaner. Service and Repair
7. Remove the battery base. Engine Removal
8. Disconnect the A/T clutch pressure control solenoid valve B connector.
9. Measure the A/T clutch pressure control solenoid valve B resistance at the connector terminals.
- If the resistance is out of standard, replace A/T clutch pressure control solenoid valve B. A/T Clutch Pressure Control Solenoid Valve A and B Replacement
- If the resistance is within the standard, go to step 10.
10. Connect a jumper wire from the negative battery terminal to the solenoid valve B connector terminal No. 2, and connect another jumper wire from the positive battery terminal to the connector terminal No. 1.
- If a clicking sound is heard, the valve is OK. Reconnect the connector, and install all removed parts.
- If no clicking sound is heard, go to step 11.
11. Remove the nuts securing the shift cable bracket (A).
12. Remove the spring clip/washer ('07 model) (B), the spring clip ('08-09 models) (C), and control pin (D), then separate the shift cable end (E) from the control lever (F).
13. Check the bushing (G) in the shift cable end for proper fit and wear. If the bushing is loose or worn, replace the shift cable. Service and Repair
14. Disconnect the input shaft (mainshaft) speed sensor connector (A), the output shaft (countershaft) speed sensor connector (B), the 3rd clutch transmission fluid pressure switch connector (C), and the ATF temperature sensor connector (D).
15. Disconnect the A/T clutch pressure control solenoid valve A connector (A), the solenoid valve B connector (B), and the shift solenoid harness connector (C).
16. Remove the bolt securing the harness cover (D).
17. Remove A/T clutch pressure control solenoid valves A and B, ATF pipes (C), gasket (D), and O-rings (E).
18. Check the fluid passage of the solenoid valve for contamination.
19. Connect a jumper wire from the negative battery terminal to A/T clutch pressure control solenoid valve B connector terminal No. 2, and connect another jumper wire from the positive battery terminal to connector terminal No. 1. Make sure A/T clutch pressure control solenoid valve B moves.
20. Disconnect one of the jumper wires, and check valve movement at the fluid passage in valve body mounting surface. If the valve binds or moves sluggishly, or if the solenoid valve does not operate, replace the A/T clutch pressure control solenoid valves A and B.
21. Clean the mounting surface and fluid passage of the solenoid valve body and solenoid valve cover.
22. Install the new solenoid valve body gasket on the solenoid valve cover, and install the ATF pipes with the filter end in the transmission housing. Install the new O-rings over the ATF pipes.
23. Install the A/T clutch pressure control solenoid valves A and B.
24. Secure the harness cover with the bolt.
25. Check the connectors for rust, dirt, or oil, clean or repair if necessary, then connect the connectors securely.
26. Apply molybdenum grease to the hole in the bushing in the shift cable end. Attach the shift cable end to the control lever, then insert the control pin into the control lever hole through the shift cable end, and secure the control pin with the spring clip/washer.
27. Secure the shift cable bracket with the nuts.
28. Install the battery base. Engine Installation
29. Install the air cleaner. Service and Repair
30. Install the charge air cooler cover.
31. Do the battery installation procedure. Removal and Replacement
32. Do the power window control unit reset procedure. Testing and Inspection
