DTC Troubleshooting
DTC Troubleshooting: P0812 (65)
DTC P0812:
Transmission Range Switch ATP R Switch
NOTE:
- Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review General Troubleshooting Information How to Troubleshoot the A/T System.
- This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
1. Turn the ignition switch to ON (II).
2. Shift to R, and verify the A/T R Switch signal with the HDS in the A/T Data List.
Is the A/T R Switch ON?
YES -
Intermittent failure, the system is OK at this time.�
NO -
Go to step 3.
3. Turn the ignition switch to LOCK (0).
4. Disconnect the transmission range switch connector.
5. Turn the ignition switch to ON (II).
6. Using a jumper wire, jump the transmission range switch connector terminal No. 8 to body ground and verify the transmission range switch signal is ON with the HDS in the A/T Data List.
Is the transmission range switch signal ON?
YES -
Replace the transmission range switch Service and Repair, then go to step 12.
NO -
Repair open in the wire between the transmission range switch and PCM connector terminal B14, then go to step 12. If circuit checks OK, go to step 7.
7. Reconnect the transmission range switch connector.
8. Update the A/T software in the PCM if it does not have the latest software PCM Update, or substitute a known-good PCM Initial Inspection and Diagnostic Overview.
9. Test-drive the vehicle in R at speeds below 3 mph(5 km/h) for at least 2 seconds, then increase the speed and test-drive at speeds over 3 mph(5 km/h) for at least 2 seconds. Slow down, and stop the wheels.
10. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0812 indicated?
YES -
If the PCM was updated, substitute a known-good PCM Initial Inspection and Diagnostic Overview, then go to step 9. If the PCM was substituted, go to step 1.
NO -
Go to step 11.
11. Monitor the OBD STATUS for P0812 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM Service and Repair. If any other Pending or Confirmed DTCs were indicated in step 10, go to the indicated DTC's troubleshooting.�
NO -
If the HDS indicates FAILED, check for poor connections or loose terminals between the transmission range switch and the PCM. If the PCM was updated, substitute a known-good PCM Initial Inspection and Diagnostic Overview, then go to step 9. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, go to step 9.
12. Reconnect the transmission range switch connector.
13. Clear the DTC with the HDS.
14. Test-drive the vehicle in R at speeds below 3 mph(5 km/h) for at least 2 seconds, then increase the speed and test-drive at speeds over 3 mph(5 km/h) for at least 2 seconds. Slow down, and stop the wheels.
15. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0812 indicated?
YES -
Check for poor connections or loose terminals between the transmission range switch and the PCM, then go to step 1.
NO -
Go to step 16.
16. Monitor the OBD STATUS for P0812 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
Troubleshooting is complete. If any other Pending or Confirmed DTCs were indicated in step 15, go to the indicated DTC's troubleshooting.�
NO -
If the HDS indicates FAILED, check for poor connections or loose terminals between the transmission range switch and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, go to step 14.