Engine Installation

Engine Installation

Special Tools Required

- Universal Lifting Eyelet 07AAK-SNAA120
- 1.8 Support Bolt 07AAK-SNAA500
- Support Eyelet 07AAK-SNAA600
- Mount Pads 07AAK-STKA120
- Subframe Adapter VSB02C000016
- Engine Support Hanger, A and Reds AAR-T1256
*Available through the Acura Tool and Equipment Program, 888-424-6857.

1. Install the engine mount bracket and the accessory brackets then tighten their bolts to the specified torque.






2. Position the engine/transmission under the vehicle. Be sure that they are properly aligned. Carefully lower the vehicle until the engine/transmission is properly positioned in the engine compartment. Make sure the vehicle is not resting on any part of the engine/transmission. Support the engine/transmission with a chain hoist (A) and carefully raise the engine/transmission into place.

NOTE: Reinstall the mounting bolts/support nuts in the sequence given in the following steps. Failure to follow this sequence may cause excessive noise and vibration, and reduce engine mount life.






3. Attach the support eyelet with the support bolt.






4. Place the mount pads over the hood edge cushions (A), and align the pins with the clip hole (B). Remove the lids from both sides of the cowl cover. Install the engine support hanger (AAR-T-1256) onto the vehicle as shown, and attach the hook to the engine support eyelet. Tighten the wing nut (C) by hand to lift and support the engine/transmission.






5. Loosen the upper torque rod mounting bolt (A).






6. Tighten the new side engine mount bracket mounting bolt and nut.






7. Remove the chain hoist.

8. Remove the universal lifting eyelet and the support bolt from the drive belt auto-tensioner.






9. Remove the transmission hanger bracket (P/N 21232-RCT-A00).






10. Install the transmission mount, then tighten the transmission mount stiffener mounting bolts (A) and the new transmission mount mounting bolts (B).





11. Loosely install the new transmission mount mounting bolt and nuts (C), then tighten to the specified torque.

12. Install the harness clamps (D).

13. Raise the vehicle on the lift.

14. Using the subframe adapter (VSB02C000016) and a jack, raise the front subframe up to the body.






15. Loosely install the new front subframe mounting 14 x 1.5 mm bolts (A), the lower arm bracket mounting 12 x 1.25 mm bolts (B), and the new front subframe mounting 12 x 1.25 mm bolts (C).






16. Align all reference marks (A) on the front subframe (B) with the body, then tighten the bolts on the front subframe to the specified torque.






17. Remove the jack and front subframe adapter.

18. Loosen install the new lower torque rod bolts, then tighten the lower torque rod mounting bolts in the numbered sequence shown.






19. Lower the vehicle on the lift.

20. Remove the special tools from the engine and vehicle.

21. Install the bracket and the seal (A) to the front grille, then install the top clips and bolts to the front grille.






22. Tighten the upper torque rod mounting bolt.






23. Raise the vehicle on the lift.

24. Loosely install the steering gearbox bracket bolts. Secure the steering gearbox mounting brackets by tighten the bolts to the specified torque.






25. Install the power steering fluid line bracket (A), and secure the hose with the hose clamps (B).






26. With SH-AWD: Install the propeller shaft to the transfer companion flange .

27. Install a new set ring on the end of each driveshaft, then install the front driveshafts Front Driveshaft Installation. Make sure each ring "clicks" into place in the differential and intermediate shaft.

28. Connect the lower arms to the knuckles Front Lower Arm Removal/Installation.

29. Connect the stabilizer links to the stabilizer bar Front Stabilizer Link Removal/Installation.

30. Install the under-floor TWC (A) Under-Floor TWC Removal/Installation. Use new gaskets (B) and new self-locking nuts (C).






31. Install the front splash shield Front Splash Shield Replacement.

32. Install the front wheels.

33. Lower the vehicle on the lift.

34. Connect the ATF cooler hoses (A), and secure the hoses with the clips (B) Service and Repair.





35. Install the ground cable (C).

36. Connect the heater hoses.






37. Install the A/C compressor (A), then connect the A/C compressor clutch connector (B).






38. Install the radiator Radiator Replacement.

39. Install the power steering pump (A), then install the power steering hose to the clamp (B).






40. Install the drive belt Service and Repair.

41. Install the shift cable Service and Repair.

42. Connect the EVAP canister hose (A), the brake booster vacuum hose (B), and the vacuum hose (C).






43. Install the heater hose clamp bracket (A), then install the heater hoses to the clamps (B).






44. Connect the fuel feed hose (A) Fuel Line/Quick-Connect Fitting Installation, then install the quick-connect fitting cover (B).






45. Install the under-hood fuse/relay box to the bracket.






46. Connect the PCM connectors (A) and the engine compartment wire harness connector (B).





47. Install the harness clamps (C).

48. Install the cables (A) to the under-hood fuse/relay box.





49. Connect the harness connector (B).

50. Install the air bypass outlet pipe (A).






51. Install the charge air cooler cover front bracket (A), then install the charge air cooler cover (B).






52. Install the battery base (A), then install the harness clamps (B) and auxiliary under-hood fuse/relay box (C).






53. Install the air cleaner Service and Repair.

54. Do the battery installation procedure Removal and Replacement.

55. Inspect for fuel leaks: Turn the ignition switch to ON (II) (do not operate the starter) so the fuel pump runs for about 2 seconds and pressurizes the fuel line. Repeat this operation three times, then check for fuel leakage at any point in the fuel line.

56. Refill the engine with engine oil Service and Repair.

57. Refill the transmission with ATF ATF Replacement.

58. Move the shift lever to each gear, and verify that the A/T gear position indicator follows the transmission range switch.

59. Refill the radiator with engine coolant. Do the cooling system bleeding procedure with the heater valve open Service and Repair.

60. Do the PCM reset procedure Initial Inspection and Diagnostic Overview.

61. Do the CKP pattern clear/CKP pattern learn procedure Initial Inspection and Diagnostic Overview.

62. Inspect the idle speed Testing and Inspection.

63. Inspect the ignition timing Testing and Inspection.

64. Check the wheel alignment Service and Repair.

65. Set the clock (on vehicles without navigation system).