General Description
DESCRIPTIONThe automatic transmission is a combination of a 3-element torque converter and triple-shaft electronically controlled automatic transmission which provides 4 speeds forward and 1 reverse. The entire unit is positioned in line with the engine.
TORQUE CONVERTER, GEARS AND CLUTCHES
The torque converter consists of a pump, turbine, and stator assembly in a single unit. They are connected to the engine crankshaft so they turn together as a unit as the engine turns. Around the outside of the torque converter is a ring gear that meshes with the starter pinion when the engine is being started. The entire torque converter assembly serves as a flywheel while transmitting power to the transmission mainshaft. The transmission has three parallel shafts: the mainshaft, the countershaft, and the secondary shaft. The mainshaft is in line with the engine crankshaft. The mainshaft includes the 3rd and 4th clutches, and gears for 3rd, 4th, reverse, and idler (reverse gear is integral with the 4th gear). The countershaft includes the final drive, 1st, 3rd, 4th, reverse, 2nd, parking, and idler gears (the final drive gear is integral with the countershaft). The secondary shaft includes the 1st and 2nd clutches, and gears for 1st, 2nd, and idler. The countershaft 4th gear and the countershaft reverse gear can be locked to the countershaft at its center, providing 4th gear or reverse, depending with which way the selector moved. The gears on the mainshaft and the secondary shaft are in constant mesh with those on the countershaft. When certain combinations of gears in the transmission are engaged by the clutches, power is transmitted from the mainshaft and the secondary shaft to the countershaft to provide [D4], [D3], [2], [1], and [R] positions.
ELECTRONIC CONTROL
The electronic control system consists of the Transmission Control Module (TCM) ('97 model), Powertrain Control Module (PCM) ('98 - '99 model), sensors, and six solenoid valves. Shifting and lock-up are electronically controlled for comfortable driving under all conditions. The TCM or PCM is located below the dashboard, under the front lower panel on the passenger's side.
HYDRAULIC CONTROL
The valve bodies include the main valve body, the regulator valve body, the servo body, and the accumulator body. They are bolted to the torque converter housing. The main valve body contains the manual valve, the modulator valve, the shift valve C, the shift valve D, the shift valve E, the servo control valve, the torque converter check valve, the reverse Clutch Pressure Control (CPC) valve, the lock-up shift valve, the relief valve, the cooler check valve, and the Automatic Transmission Fluid (ATF) pump gears. The regulator valve body contains the regulator valve, the lock-up timing valve, and the lock-up control valve. The servo body contains the servo valve, the shift valve A, the shift valve B, the CPC valves A and B, and the 3rd and 4th accumulators. The accumulator body contains the 1st and 2nd accumulators and lubrication check valve. Fluid from the regulator passes through the manual valve to the various control valves. The 1st, 3rd, and 4th clutches receive fluid from their respective feed pipes, and the 2nd clutch receives fluid from the internal hydraulic circuit.
SHIFT CONTROL MECHANISM
The Transmission Control Module (TCM) or Powertrain Control Module (PCM) controls, shift control solenoid valves A, B, and C, and Automatic Transaxle (A/T) Clutch Pressure Control (CPC) solenoid valves A and B while receiving input signal from various sensors located throughout the vehicle. The shift control solenoid valves shift the positions of the shift valves to switch the port leading hydraulic pressure to the clutch. The A/T CPC solenoid valves A and B control the CPC valves A and B, to shift smoothly between lower gear and higher gear. This pressurizes a line to one of the clutches, engaging the clutch and its corresponding gear.
LOCK-UP MECHANISM
In [D4] position (3rd and 4th) and [D3] position (3rd) pressurized fluid is drained from the back of the torque converter through a fluid passage, causing the lock-up piston to be held against the torque converter cover. As this takes place, the mainshaft rotates at the same speed as the engine crankshaft. Together with hydraulic control, the Transmission Control Module (TCM) or Powertrain Control Module (PCM) optimizes the timing of the lock-up mechanism. When the lock-up control solenoid valve activates, modulator pressure changes to switch lockup on and off. The lock-up control valve and the lock-up timing valve control the range of lock-up according to Automatic Transaxle (A/T) Clutch Pressure Control (CPC) solenoid valves A and B. The lock-up control solenoid valve is mounted on the torque converter housing, and A/T CPC solenoid valves A and B are mounted on the transmission housing. They are all controlled by the TCM or PCM.
GEAR SELECTION
The shift lever has seven positions: [P] PARK, [R] REVERSE, [N] NEUTRAL, [D4] 1st through 4th gear ranges, [D3] 1st through 3rd gear ranges, [2] 2nd gear, and [1] 1st gear.
Starting is possible only in [P] and [N] positions through the use of a slide-type, neutral-safety switch.
AUTOMATIC TRANSAXLE (A/T) GEAR POSITION INDICATOR
The Automatic Transaxle (A/T) gear position indicator in the instrument panel shows which gear has been selected without having to look down at the console.
NOTE: The Vehicle Speed Sensor (VSS) is present only on the '97 model.