Engine Assembly

Block	Warpage of deck		Standard or new	0.07 mm Maximum
			Service limit	0.10 mm
	Bore diameter	A or I	Standard or new	86.010 - 86.020 mm
			Service limit	86.070 mm
		B or II	Standard or new	86.000 - 86.010 mm
			Service limit	86.070 mm
	Bore taper		Service limit	0.05 mm
	Reboring limit		Service limit	0.25 mm
Piston	Skirt O.D. at 11 mm (0.4 inch) from bottom of skirt	No letter or A	Standard or new	85.980 - 85.990 mm
			Service limit	85.930 mm
		Letter B	Standard or new	85.970 - 85.980 mm
			Service limit	85.920 mm
	Clearance in cylinder		Standard or new	0.020 - 0.040 mm
			Service limit	0.05 mm
	Ring groove width	Top	Standard or new	1.220 - 1.230 mm
			Service limit	1.25 mm
		Second	Standard or new	1.220 - 1.230 mm
			Service limit	1.25 mm
		Oil	Standard or new	2.005 - 2.025 mm
			Service limit	2.05 mm
Piston ring	Ring-to-groove clearance	Top	Standard or new	0.035 - 0.060 mm
			Service limit	0.13 mm
		Second	Standard or new	0.030 - 0.055 mm
			Service limit	0.13 mm
	Ring end gap	Top	Standard or new	0.20 - 0.35 mm
			Service limit	0.60 mm
		Second	Standard or new	0.40 - 0.55 mm
			Service limit	0.70 mm
		Oil	Standard or new	0.25 - 0.65 mm
			Service limit	0.75 mm
Piston pin	O.D.		Standard or new	21.961 - 21.965 mm
			Service limit	21.953 mm
	Pin-to-piston clearance		Standard or new	-0.005 - +0.002 mm
			Service limit	21.953 mm
Connecting rod	Pin-to-rod clearance		Standard or new	0.005 - 0.015 mm
			Service limit	0.02 mm
	Small-end bore diameter		Standard or new	21.970 - 21.976 mm
	Large-end bore diameter (Normal)		Standard or new	48.0 mm
	End play installed on crankshaft		Standard or new	0.15 - 0.30 mm
			Service limit	0.40 mm
Crankshaft	Main journal diameter	No.1 journal	Standard or new	54.984 - 55.008 mm
		No.2 journal	Standard or new	54.984 - 55.008 mm
		No.4 journal	Standard or new	54.984 - 55.008 mm
		No.5 journal	Standard or new	54.984 - 55.008 mm
		No.3 journal	Standard or new	54.976 - 55.000 mm
	Rod journal diameter		Standard or new	44.976 - 45.000 mm
	Rod/main journal taper		Standard or new	0.005 mm
			Service limit	0.010 mm
	Rod/main journal out-of-round		Standard or new	0.005 mm
			Service limit	0.010 mm
	End play		Standard or new	0.10 - 0.35 mm
			Service limit	0.45 mm
	Runout		Standard or new	0.03 mm Maximum
			Service limit	0.04 mm
Crankshaft bearings	Main bearing-to-journal oil clearance	No.1 journal	Standard or new	0.017 - 0.041 mm
			Service limit	0.050 mm
		No.2 journal	Standard or new	0.017 - 0.041 mm
			Service limit	0.050 mm
		No.4 journal	Standard or new	0.017 - 0.041 mm
			Service limit	0.050 mm
		No.5 journal	Standard or new	0.017 - 0.041 mm
			Service limit	0.050 mm
		No.3 journal	Standard or new	0.025 - 0.049 mm
			Service limit	0.055 mm
	Rod bearing clearance		Standard or new	0.021 - 0.049 mm
			Service limit	0.060 mm