Transmission Installation
Transmission InstallationNOTE: Use fender covers to avoid damaging painted surfaces.
1. Install the vacuum line on the transmission.
2. Install the torque converter assembly (A) on the mainshaft (B) with the new O-ring (C).
3. Install the 14 x 20 mm dowel pin (D) and 10 x 20 mm dowel pin (E) in the torque converter housing.
4. Place the transmission on the jack, and raise the transmission to the engine level.
5. Attach the transmission to the engine, then install the transmission housing mounting bolts.
6. Install the transmission housing mounting bolts.
7. Remove the jack from the transmission.
8. Install the front mount bracket with the new bolts, and install the harness clamp on the mount bracket.
9. Install the engine-to-torque converter housing mounting bolts.
10. Attach the torque converter to the drive plate (A) with eight bolts (B).Rotate the crankshaft pulley as necessary to tighten the bolts to 1/2 of the specified torque, then to the final torque, in a crisscross pattern. After tightening the last bolt, check that the crankshaft rotate freely.
11. Install the torque converter cover (C).
12. Install the new ret ring (A) on the intermediate shaft (B).
13. Install the exhaust manifold bracket (C) and heat shield (D).
14. Install the new set ring on the left driveshaft, then install the led driveshaft in the differential. While installing the driveshaft in the differential, be sure not to allow dust or other foreign particles to enter the transmission. Install the left driveshaft over the intermediate shaft.
NOTE:
- Clean the a reas where the driveshaft and intermedial e shaft contact the transmission (differential) with solvent or carburetor cleaner, and dry with compressed air.
- Turn the right and left steering knuckle fully outward, and slide the driveshaft and intermediate shaft into the differential and intermediate shaft until you feel its set ring engage the side gear.
15. Install the transmission lower front mount (A).
16. Install the transmission lower rear mount (B) with the new bolts.
17. Support the front subframe (A) with the special tool and a lack, and lift it up to body.
18. Loosely install the new subframe mounting bolts (A), and new rear stiffener mounting bolts (B), and the front stiffener mounting bolts (C).
19. Loosely install both of the new both mid-mount mounting bolts.
20. Align the reference marks (A) with edge (B) of both rear stiffeners (C), and tighten the rear subframe mounting bolts, then front bolts, and tighten the stiffener bolts to the specified torque.
21. Tighten the mid-mount mounting bolts.
22. Install the new rear mount bracket bolts.
23. Install the new transmission lower mount nuts.
24. Connect the power steering pressure switch connector.
25. Connect the power steering hose to the power steering line.
26. Install control lever (A) on the control shaft (B). Do not bend the shift cable excessively.
27. Install the lock bolt (C) with a new lock washer (D), then bend the lock washer tab against the bolt head.
28. Install the shift cable cover (E), then secure the shift cable holder (F) on the cover with the bolts.
NOTE: To prevent damage to the control lever joint, be sure install the shift cable holder after installing the shift cable cover to the torque converter housing.
29. Install the steering gearbox heat shield (A).
30. Install exhaust pipe A with the new self-locking nuts, its mount (B), and new gaskets (C) (D).
31. Install the damper forks (A) with damper pinch bolts (B) and the new self-locking nuts (C), then install the ball joints on the lower arms (D) with the ball joint nuts (E) and new cotter pins (F).
32. Install the tie-rod end ball joints (G) to each knuckle with the nuts (H) and new cotter pins (I).
33. Install the stabilizer links (J) to the lower arms, and install the nuts (K). Insert a 6 mm Allen wrench (L) in the ball joint (M), and tighten the nuts.
34. Install the new front mount bolt (A).
35. Install the front mount stop (B).
36. Remove the engine hanger and engine balancer bar.
37. Install the harness clamp bracket to the engine rear cylinder head.
38. Install the connector bracket to the engine front cylinder head.
39. Install the ATF warmer (A) with new O-rings (B) and the bracket (C) on the transmission housing. Do not pinch the O-rings.
40. Install the transmission ground cable (D), and connect the breather tube (E).
41. Install the harness clamp bracket (A), and install the harness cover (B) on the bracket (C).
42. Install the harness clamps (D) on the clamp brackets.
43. Connect the output shaft (countershaft) speed sensor connector (A), and install the harness clamps (B) on the brackets. Connect the vacuum hose (C) to the vacuum line (D).
44. Connect the transmission range switch connector (E), then install it on its bracket (F).
45. Connect the connectors to the torque converter clutch solenoid valve (A) and shift solenoid valve B.
46. Connect the A/T clutch pressure control solenoid valve A connector, and solenoid valve B connector, and install the harness clamp (C) on the clamp bracket (D).
47. Connect shift solenoid valve A connector, solenoid valve C connector, and A/T clutch pressure control solenoid valve C connector (B), and install the harness clamps (D) on the clamp brackets (E).
48. Connect the input shaft (mainshaft) speed sensor connector (A) and 4th clutch transmission fluid pressure switch connector (B), and connect the vacuum hove (C) to the vacuum line (D).
49. Connect the transmission subharness connector (E), then install it on its bracket (F).
50. Install the transmission upper mount bracket (A) on the transmission with two bolts.
51. Install the new upper mount bolt and bracket plate (B).
52. Install the starter (A) on the torque converter housing. Connect the starter cables (B) to the starter, and install the harness clamp on the clamp bracket.
53. Insert the power steering pump outlet fine (A) with a new O-ring (B) to the pump (C). and install the hose (D) in its clamp (E).
54. Refill the power steering fluid reservoir with fluid to the upper level line.
55. Install the strut brace (A).
56. Install the two 6.0 mm bolts, and install the harness clamp (B) on its clamp bracket.
57. Refill the transmission with ATF.
58. Install the battery base, and install the resonator and resonator cover.
59. Install the air cleaner housing and intake air duct.
60. Install the battery tray and battery, then secure the battery with its hold-down bracket.
61. Connect the steering joint to the steering gearbox pinion shaft (A) by aligning the reference mark (B), and remove the wire (C) from the joint yoke (D).
62. Install the steering joint cover (E).
63. Remove the steering wheel.
64. Center the SRS cable reel and reinstall the steering wheel.
65. Connect the battery terminals.
66. Install the splash shield.
67. Install the transmission under cover.
68. Install the covers in the order presented; intake manifold cover (A), front bulkhead cover (B), left fender trim (C), right rear engine compartment cover (D), right side engine compartment cover (E), right fender trim (F), left rear engine compartment cover (G), and left side engine compartment cover (H).
69. Reinstall the hood support struts to the proper locations on both sides of the hood.
70. Set the parking brake. Start the engine, and shift the transmission through all gears three times.
71. Start the engine, and run it fast idle, then turn the steering wheel from lock-to-lock several times to bleed air from the system.
72. Recheck the fluid level, and refill if necessary.
73. Check the shift lever operation, A/T gear position indicator operation, and shift cable adjustment.
74. Check and adjust the front wheel alignment.
75. Start the engine in the P or N position, and warm it up to normal operating temperature (the radiator fan comes on).
76. Turn off the engine, and check the ATF level.
77. Perform the road test.
78. Enter the radio and navigation anti-theft codes, and set the XM radio channel presets and the clock.