P0223
DTC P0223: TP Sensor B Circuit High VoltageNOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information.
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Check TP SENSOR A in the DATA LIST with the HDS.
Is there about 4.8 V or more?
YES - Go to step 4.
NO - Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the throttle body and the throttle actuator control module.
4. Check for Temporary DTCs or DTCs with the HDS.
Are DTC P0123 and P0223 indicated at the same time?
YES - Go to step 13.
NO - Go to step 5.
5. Measure voltage between throttle body 6P connector terminal No. 3 and body ground.
Is there about 5 V?
YES - Go to step 20.
NO - Go to step 6.
6. Turn the ignition switch OFF.
7. Disconnect the throttle body 6P connector.
8. Disconnect the C251 connector (13P) between the PCM subharness and the throttle actuator control module subharness.
9. Connect throttle body 6P connector terminal No. 3 to body ground with a jumper wire.
10. Check for continuity between C251 connector (13P) terminal No. 2 and body ground.
Is there continuity?
YES - Go to step 11.
NO - Repair open in the wire between the throttle body and the C251 connector (TPSB line), then go to step 22.
11. Disconnect the throttle actuator control module 16P connector.
12. Check for continuity between throttle actuator control module 16P connector terminal No. 12 and C251 connector (13P) terminal No. 2.
Is there continuity?
YES - Substitute a known-good throttle actuator control module, then go to step 22 and recheck. If DTC P0223 is not indicated, replace the original throttle actuator control module, then go to step 22. If DTC P0223 is indicated, go to step 20.
NO - Repair open in the wire between the throttle actuator control module and the C251 connector (TPSB line), then go to step 22.
13. Turn the ignition switch OFF.
14. Disconnect the throttle body 6P connector.
15. Disconnect the C251 connector (13P) between the PCM subharness and the throttle actuator control module subharness.
16. Connect throttle body 6P connector terminal No. 4 to body ground with a jumper wire.
17. Check for continuity between C251 connector (13P) terminal No. 5 and body ground.
Is there continuity?
YES - Go to step 18.
NO - Repair open in the wire between the throttle body and the C251 connector (SG line), then go to step 22.
18. Disconnect the throttle actuator control module 16P connector.
19. Check for continuity between throttle actuator control module 16P connector terminal No. 9 and C251 connector (13P) terminal No. 5.
Is there continuity?
YES - Substitute a known-good throttle actuator control module, then go to step 22 and recheck. If DTC P0223 is not indicated, replace the original throttle actuator control module, then go to step 22. If DTC P0223 is indicated, go to step 20.
NO - Repair open in the wire between the throttle actuator control module (SG line) and the C251 connector, then go to step 22.
20. Turn the ignition switch OFF
21. Replace the throttle body.
22. Reconnect all connectors.
23. Turn the ignition switch ON (II).
24. Reset the PCM with the HDS.
25. Do the PCM idle learn procedure.
26. Check for Temporary DTCs or DTCs with the HDS.
Are any Temporary DTCs or DTCs indicated?
YES - If DTC P0223 is indicated, check for poor connections or loose terminals at the throttle body and the throttle actuator control module, then go to step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.
NO - Troubleshooting is complete.