P0563
DTC P0563: PCM Power Source Circuit Unexpected VoltageNOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information.
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch OFF.
4. Wait 10 seconds.
5. Turn the ignition switch ON (II).
6. Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0563 indicated?
YES - Go to step 7.
NO - Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at PGM-FI main relay 1 (FI MAIN) and the No. 8 FI-ECU (PCM) (15 A) fuse in the under-hood fuse/relay box, and the PCM.
7. Turn the ignition switch OFF.
8. Jump the SCS line with the HDS.
9. Disconnect PCM connector E (31P).
10. Measure voltage between PCM connector terminal E5 and body ground.
Is there battery voltage?
YES - Go to step 13.
NO - Go to step 11.
11. Remove the left kick panel (see step 3). Then remove PGM-FI main relay 1 (FI MAIN) (A) from the under-dash fuse/relay box.
12. Check for continuity between PCM connector terminal E5 and body ground.
Is there continuity?
YES - Repair short in the wire between the PCM (E5) and PGM-FI main relay 1 (FI MAIN), then go to step 20.
NO - Go to step 19.
13. Reconnect PCM connector E (31P).
14. Measure voltage between PCM connector terminal E5 and body ground.
Is there battery voltage?
YES - Go to step 15.
NO - Go to step 27.
15. Disconnect PCM connector A (31P).
16. Measure voltage between PCM connector terminal A4 and body ground.
Is there battery voltage?
YES - Go to step 17.
NO - Go to step 27.
17. Remove the left kick panel. Then remove PGM-FI main relay 1 (FI MAIN) (A) from the under-dash fuse/relay box.
18. Measure voltage between PCM connector terminal A4 and body ground.
Is there battery voltage?
YES - Repair short to power in the wire between the PCM (A4) and PGM-FI main relay 1 (FI MAIN), then go to step 20.
NO - Go to step 19.
19. Replace PGM-FI main relay 1 (FI MAIN) (A).
20. Reconnect all connectors.
21. Turn the ignition switch ON (II).
22. Reset the PCM with the HDS.
23. Turn the ignition switch OFF.
24. Wait 10 seconds.
25. Do the PCM idle learn procedure.
26. Check for Temporary DTCs or DTCs with the HDS.
Are any Temporary DTCs or DTCs indicated?
YES - If DTC P0563 is indicated, check for poor connections or loose terminals at PGM-FI main relay 1 (FI MAIN) and the PCM, then go to step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.
NO - Troubleshooting is complete.
27. Update the PCM if it does not have the latest software, or substitute a known-good PCM.
28. Check for Temporary DTCs or DTCs with the HDS.
Are any Temporary DTCs or DTCs indicated?
YES - If DTC P0563 is indicated, check for poor connections or loose terminals at PGM-FI main relay 1 (FI MAIN) and the PCM, then go to step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.
NO - If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM.