P0135
DTC P0135: A/F Sensor (Sensor 1) Heater Circuit Malfunction (2005-2006 models)1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on, then let it idle.
4. Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0135 indicated?
YES - Go to step 5.
NO - Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the A/F sensor (Sensor 1), the A/F sensor relay and the ECM/PCM.
5. Turn the ignition switch OFF.
6. Check these fuses:
- No. 14 OPTION (30 A) fuse in under-hood fuse/relay box.
- No. 2 +B LAF (A/F) HEATER (20 A) fuse in under-dash fuse/relay box.
- No. 4 ACG (10 A) fuse in under-dash fuse/relay box.
Are any of the fuses blown?
YES - Repair short in the wire between the A/F sensor relay and the fuses, then go to step 25.
NO - Go to step 7.
7. Disconnect the A/F sensor (Sensor 1) 4P connector.
8. At the A/F sensor side, measure resistance between A/F sensor (Sensor 1) 4P connector terminals No. 3 and No. 4.
Is there 2.1 - 2.9 Ohms at room temperature?
YES - Go to step 9.
NO - Go to step 24.
9. At the A/F sensor side, check for continuity between A/F sensor (Sensor 1) 4P connector terminal No. 2 and A/F sensor (Sensor 1) 4P connector terminals No. 3 and No. 4 individually.
Is there continuity?
YES - Go to step 24.
NO - Go to step 10.
10. Jump the SCS line with the HDS.
11. Disconnect ECM/PCM connector A (31P).
12. Check for continuity between ECM/PCM connector terminal A10 and body ground.
Is there continuity?
YES - Repair short in the wire between the ECM/PCM (A10) and the A/F sensor (Sensor 1), then go to step 25.
NO - Go to step 13.
13. Connect A/F sensor (Sensor 1) 4P connector terminal No. 4 to body ground with a jumper wire.
14. Check for continuity between ECM/PCM connector terminal A10 and body ground.
Is there continuity?
YES - Go to step 15.
NO - Repair open in the wire between the ECM/PCM (A10) and the A/F sensor (Sensor 1), then go to step 25.
15. Remove the A/F sensor relay (A).
16. Check the A/F sensor relay.
Is the A/F sensor relay OK?
YES - Go to step 17.
NO - Replace the A/F sensor relay, then go to step 25.
17. Connect A/F sensor (Sensor 1) 4P connector terminal No. 3 to body ground with a jumper wire.
18. Check for continuity between A/F sensor relay 4P connector terminal No. 1 and body ground.
Is there continuity?
YES - Go to step 19.
NO - Repair open in the wire between the A/F sensor (Sensor 1) and the A/F sensor relay, then go to step 25.
19. Disconnect ECM/PCM connector E (31P).
20. Check for continuity between ECM/PCM connector terminal E8 and A/F sensor relay 4P connector terminal No. 3.
Is there continuity?
YES - Go to step 21.
NO - Repair open in the wire between the ECM/PCM (E8) and the A/F sensor relay, then go to step 25.
21. Measure voltage between A/F sensor relay 4P connector terminal No. 2 and body ground.
Is there battery voltage?
YES - Go to step 22.
NO - Repair open in the wire between the A/F sensor relay and the No. 2 +B LAF (A/F) HEATER (20 A) fuse, then go to step 25.
22. Turn the ignition switch ON (II).
23. Measure voltage between A/F sensor relay 4P connector terminal No. 4 and body ground.
Is there battery voltage?
YES - Go to step 31.
NO - Repair open in the wire between the A/F sensor relay and the No. 4 ACG (10 A) fuse, then go to step 25.
24. Replace the A/F sensor (Sensor 1).
25. Reconnect all connectors.
26. Turn the ignition switch ON (II).
27. Reset the ECM/PCM with the HDS.
28. Do the ECM/PCM idle learn procedure.
29. Check for Temporary DTCs or DTCs with the HDS.
Are any Temporary DTCs or DTCs indicated?
YES - If DTC P0135 is indicated, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.
NO - Go to step 30.
30. Monitor the OBD STATUS for DTC P0135 in the DTCs MENU with the HDS.
Does the screen indicate PASSED?
YES - Troubleshooting is complete.
NO - If the screen indicates FAILED, check for poor connections or loose terminals at the A/F sensor (Sensor 1) and the ECM/PCM, then go to step 1. If the screen indicates NOT COMPLETED, go to step 28 and recheck.
31. Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM.
32. Check for Temporary DTCs or DTCs with the HDS.
Are any Temporary DTCs or DTCs indicated?
YES - If DTC P0135 is indicated, check for poor connections or loose terminals at the A/F sensor (Sensor 1), and the A/F sensor relay and the ECM/PCM, then go to step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.
NO - If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was substituted, replace the original ECM/PCM.