P0300
DTC P0300: Random Misfire Detected and Any Combination of the Following: (2005-2006 models)DTC P0301: No. 1 Cylinder Misfire Detected (2005-2006 models)
DTC P0302: No. 2 Cylinder Misfire Detected (2005-2006 models)
DTC P0303: No. 3 Cylinder Misfire Detected (2005-2006 models)
DTC P0304: No. 4 Cylinder Misfire Detected (2005-2006 models)
Special Tools Required
- Pressure gauge adapter 07NAJ-P07010A
- A/T low pressure gauge w/panel 07406-0070300
- A/T pressure hose 07406-0020201
- A/T pressure hose, 2,210 mm 07MAJ-PY4011A
- A/T pressure hose, adapter 07MAJ-PY40120
- Oil pressure hose 07ZAJ-S5A0200
NOTE:
- If the misfire is frequent enough to trigger detection of increased emissions during 2 consecutive driving cycles, the MIL will come on, and DTC P0300 (and some combination of P0301 through P0304) will be stored.
- If the misfire is frequent enough to damage the catalyst, the MIL will flash whenever the misfire occurs, and DTC P0300 (and some combination of P0301 through P0304) will be stored. When the misfire stops, the MIL will remain on.
- Troubleshoot the following DTCs first, if any of them were stored along with the random misfire DTC(s):
P0107, P0108, P1128, P1129: Manifold absolute pressure (MAP) sensor
P0171, P0172: Fuel system
P0335, P0339: Crankshaft position (CKP) sensor
P0365, P0369: Camshaft position (CMP) sensor B
P0506, P0507: Idle control system
1. Record all freeze data and on-board snapshots with the HDS.
2. Clear the DTC with the HDS.
3. Start the engine (in Park or neutral), then let it idle without load.
4. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Does the screen indicate FAILED?
YES - Go to step 9.
NO - If the screen indicates PASSED, go to step 5. If the screen indicates EXECUTING, keep driving until a result comes on. If the screen indicates OUT OF CONDITION, wait for several minutes, and recheck.
5. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST for 10 minutes with the HDS.
Does CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE show misfire counts?
YES - Go to step 9.
NO - Go to step 6.
6. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
- Engine speed
- Vehicle speed
- Throttle position
- CLV (calculated load value)
- Gear position
7. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Does the screen indicate FAILED?
YES - Go to step 9.
NO - If the screen indicates PASSED, go to step 8. If the screen indicates EXECUTING, keep driving until a result comes on. If the screen indicates OUT OF CONDITION, go to step 6 and recheck.
8. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST for 10 minutes with the HDS.
Does CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE show misfire counts?
YES - Go to step 9.
NO - Intermittent failure, system is OK at this time.
9. Turn the ignition switch OFF.
10. Check the fuel quality.
Is the quality good?
YES - Go to step 11.
NO - Drain the tank and fill it with known-good fuel, then go to step 20.
11. Inspect the spark plugs. If the spark plugs are fouled or worn, replace them.
12. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
- Engine speed
- Vehicle speed
- Throttle position
- CLV (calculated load value)
- Gear position
13. Check the CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE in the DATA LIST for 10 minutes with the HDS.
Does CYL1 MISFIRE, CYL2 MISFIRE, CYL3 MISFIRE, and/or CYL4 MISFIRE show misfire counts?
YES - Go to step 14.
NO - Go to step 20.
14. Check the fuel pressure.
Is the fuel pressure OK?
YES - Go to step 15.
NO -
- If the pressure is too high, replace the fuel pressure regulator, then go to step 20.
- If the pressure is too low, check the fuel pump, the fuel feed pipe, and the fuel filter. If they are OK, replace the fuel pressure regulator , then go to step 20.
15. Turn the ignition switch OFF.
16. Remove the rocker arm oil pressure switch (VTEC oil pressure switch) (A), and install the special tools as shown, then install the rocker arm oil pressure switch (VTEC oil pressure switch) (A) in the pressure gauge adapter (B).
NOTE: Install the switch in the reverse order of removal with a new O-ring.
17. Reconnect the rocker arm oil pressure switch (VTEC oil pressure switch) 2P connector.
18. Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on.
19. Check the oil pressure at engine speeds of 1,000 and 2,000 rpm. Keep the test time as short as possible (less than 1 minute) because the engine is running without load.
Is the oil pressure below 49 kPa (0.5 kgf/sq.cm, 7 psi)?
YES - Check the fuel pressure, and repair as needed, then go to step 20.
NO - Inspect the VTEC system, then go to step 20.
20. Turn the ignition switch ON (II).
21. Reset the ECM/PCM with the HDS.
22. Clear the CKP pattern with the HDS.
23. Do the ECM/PCM idle learn procedure.
24. Do the CKP pattern learn procedure.
25. Test-drive the vehicle for several minutes in the range of these recorded freeze data parameters:
- Engine speed
- Vehicle speed
- Throttle position
- CLV (calculated load value)
- Gear position
26. Check for Temporary DTCs or DTCs with the HDS.
Are any Temporary DTCs or DTCs indicated?
YES - If DTC P0300, P0301, P0302, P0303, or P0304 are indicated, check for poor connections or loose terminals at the ignition coil, the injector, and the ECM/PCM, then go to troubleshooting DTC P0301, P0302, P0303, or P0304. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.
NO - Go to step 27.
27. Monitor the OBD STATUS for DTC P0301, P0302, P0303, or P0304 in the DTCs MENU with the HDS.
Does the screen indicate PASSED?
YES - Troubleshooting is complete.
NO - If the screen indicates FAILED, go to step 1 and recheck. If the screen indicates EXECUTING, keep driving until a result comes on. If the screen indicates OUT OF CONDITION, go to step 25 and recheck.