B1827
DTC B1827: Power Seat Rear Up-down Motor Pulse ErrorNOTE:
- If you are troubleshooting multiple DTCs, be sure to follow the instructions in B-CAN System Diagnosis Test Mode A.
- DTC B1827 is stored when the rear up-down switch is operated more than 1 second after the seat moves to the most up or most down position, even when the system is OK.
1. Clear the DTCs with the HDS.
2. Turn the ignition switch OFF, and then back ON (II).
3. Operate the power seat adjustment switch in each direction for more than 1 second.
4. Check for the DTCs with the HDS.
Is DTC B1827 indicated?
YES - Go to step 5.
NO - Intermittent failure, the rear up-down motor/position sensor is OK at this time. Check for loose or poor connections at the power seat control unit connector.
5. Check for DTCs with the HDS.
Are DTCs B1825, B1826 and/or B1828 also indicated?
YES - Go to step 17.
NO - Go to step 6.
6. Clear the DTCs with the HDS.
7. Turn the ignition switch OFF, and then back ON (II).
8. Operate the rear up-down switch for 2 seconds, and check the rear up-down motor operation.
Does the rear up-down motor run smoothly?
YES - Go to step 9.
NO - Go to step 26.
9. Turn the ignition switch OFF.
10. Disconnect power seat control unit connector A (40P).
11. Disconnect the rear up-down motor/position sensor 5P connector.
12. Check for continuity between power seat control unit connector A (40P) terminals No. 13 and No. 29 and rear up-down motor/position sensor 5P connector terminals No. 5 and No. 4 respectively.
Is there continuity?
YES - Go to step 13.
NO - Repair an open in the wire.
13. Check for continuity between power seat control unit connector A (40P) terminal No. 13 and body ground.
Is there continuity?
YES - Repair a short in the wire.
NO - Go to step 14.
14. Reconnect power seat control unit connector A (40P).
15. Turn the ignition switch ON (II).
16. Measure voltage between rear up-down motor/position sensor 5P connector terminals No. 5 (+) and No. 4 (-).
Is there about 5 V?
YES - Replace the rear up-down motor/position sensor.
NO - If there is no voltage, replace the power seat control unit. If there is battery voltage, repair a short in the wire (sensor line).
17. Turn the ignition switch OFF.
18. Disconnect power seat control unit connector A (40P).
19. Disconnect the rear up-down motor/position sensor 5P connector.
20. Check for continuity between power seat control unit connector A (40P) terminals No. 15 and No. 29 and rear up-down motor/position sensor 5P connector terminals No. 3 and No. 4 respectively.
Is there continuity?
YES - Go to step 21.
NO - Repair an open in the wire.
21. Disconnect the slide position sensor 3P connector and each 5P connector from the recline motor/position sensor and the front up-down motor/position sensor.
22. Check for continuity between rear up-down motor/position sensor terminal No. 3 and body ground.
Is there continuity?
YES - Repair a short in the wire.
NO - Go to step 23.
23. Reconnect power seat control unit connector A (40P).
24. Turn the ignition switch ON (II).
25. Measure voltage between power seat control unit connector A (40P)terminals No. 15 and No. 29.
Is there battery voltage when the rear up-down switch is operated?
YES - Replace the rear up-down motor/position sensor.
NO - Replace the power seat control unit.
26. Turn the ignition switch OFF.
27. Disconnect power seat control unit connector B (18P).
28. Disconnect the rear up-down motor/position sensor 5P connector.
29. Check for continuity between power seat control unit connector B (18P) terminals No. 2 and No. 10 and rear up-down motor/position sensor 5P connector terminals No. 1 and No. 2 respectively.
Is there continuity?
YES - Go to step 30.
NO - Repair an open in the wire.
30. Check for continuity between body ground and rear up-down motor/position sensor 5P connector terminals No. 1 and No. 2 individually.
Is there continuity?
YES - Repair a short in the wire.
NO - Go to step 31.
31. Do the rear up-down motor test.
Is the motor OK?
YES - Replace the power seat control unit.
NO - Replace the rear up-down motor/position sensor.