DTC Troubleshooting
DTC P0847: Short in 3rd Clutch Transmission Fluid Pressure Switch Circuit, or 3rd Clutch Transmission Fluid Pressure Switch Stuck ONNOTE:
- Before you troubleshoot, record all freeze data and any on-board snapshot, and review General Troubleshooting Information.
- This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
1. Clear the DTC with the HDS.
2. Check the 3rd PRESSURE SWITCH SIGNAL with the HDS in the A/T data list when not in 3rd gear.
Is the 3rd PRESSURE SWITCH OFF?
YES - Go to step 3.
NO - Go to step 6.
3. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
4. Drive the vehicle in 3rd gear in the M position for more than 5 seconds, then upshift to 4th gear, and drive in 4th gear for more than 5 seconds. Slow down and stop the wheels.
5. Monitor the OBD STATUS for P0847 in the DTCs MENU with the HDS.
Does the screen indicate FAILED?
YES - Go to step 6.
NO - If the screen indicates PASSED, intermittent failure, the system is OK at this time. Check the OP3 SW (BLU/WHT) wire for an intermittent short to body ground between the 3rd clutch transmission fluid pressure switch and the PCM. If the screen indicates NOT COMPLETED, return to step 3 and recheck.
6. Turn the ignition switch OFF.
7. Disconnect the 3rd clutch transmission fluid pressure switch connector.
8. Turn the ignition switch ON (II).
9. Check the 3rd PRESSURE SWITCH SIGNAL with the HDS in the A/T data list.
Is the 3rd PRESSURE SWITCH OFF?
YES - Replace the 3rd clutch transmission fluid pressure switch, then go to step 14.
NO - Go to step 10.
10. Turn the ignition switch OFF.
11. Jump the SCS line with the HDS.
12. Disconnect PCM connector C (22P).
13. Check for continuity between PCM connector terminal C9 and body ground.
Is there continuity?
YES - Repair a short to body ground in the wire between PCM connector terminal C9 and the 3rd clutch transmission fluid pressure switch, then go to step 14.
NO - Go to step 21.
14. Reconnect all connectors.
15. Turn the ignition switch ON (II).
16. Clear the DTC with the HDS.
17. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
18. Drive the vehicle in 3rd gear in the M position for more than 5 seconds, then upshift to 4th gear, and drive in 4th gear for more than 5 seconds. Slow down and stop the wheels.
19. Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0847 indicated?
YES - Check for poor connections or loose terminals at the 3rd clutch transmission fluid pressure switch and the PCM, then go to step 1.
NO - Go to step 20.
20. Monitor the OBD STATUS for P0847 in the DTCs MENU with the HDS.
Does the screen indicate PASSED?
YES - Troubleshooting is complete.
NO - Return to step 6 and recheck.
21. Update the PCM if it does not have the latest software, or substitute a known-good PCM.
22. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
23. Drive the vehicle in 3rd gear in the M position for more than 5 seconds, then upshift to 4th gear, and drive in 4th gear for more than 5 seconds. Slow down and stop the wheels.
24. Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0847 indicated?
YES - Check for poor connections or loose terminals at the 3rd clutch transmission fluid pressure switch and the PCM. If the PCM was updated, substitute a known-good PCM, then go to step 22. If the PCM was substituted, go to step 1.
NO - Go to step 25.
25. Monitor the OBD STATUS for P0847 in the DTCs MENU with the HDS.
Does the screen indicate PASSED?
YES - Troubleshooting is complete.
NO - Return to step 6 and recheck.