DTC Troubleshooting
DTC P0325: Knock Sensor Circuit MalfunctionNOTE: Before you troubleshoot, record all freeze data and any onboard snapshot, and review the general troubleshooting information.
1. Turn the ignition switch ON (II).
2. Clear the DTC with the HDS.
3. Start the engine. Hold the engine speed at 3,000 rpm without load (in Park or neutral) until the radiator fan comes on, then let it idle.
4. Hold the engine speed at 3,000 - 4,000 rpm for at least 10 seconds.
5. Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0325 indicated?
YES - Go to step 6.
NO - Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the knock sensor and the ECM/PCM.
6. Turn the ignition switch OFF.
7. Jump the SCS line with the HDS.
8. Disconnect the knock sensor subharness 1P connector.
9. Disconnect ECM/PCM connector B (24P).
10. Check for continuity between ECM/PCM connector terminal B6 and body ground.
Is there continuity?
YES - Repair short in the wire between the ECM/PCM (B6) and the knock sensor subharness, then go to step 19.
NO - Go to step 11.
11. Connect the engine wire harness 1P connector (C154) terminal to body ground with a jumper wire.
12. Check for continuity between ECM/PCM connector terminal B6 and body ground.
Is there continuity?
YES - Go to step 13.
NO - Repair open in the wire between the ECM/PCM (B6) and the knock sensor subharness, then go to step 19.
13. Remove the intake manifold, and injector base.
14. Disconnect the knock sensor 1P connector.
15. Check for continuity between the knock sensor subharness 1P connector terminal and body ground.
Is there continuity?
YES - Repair short in the knock sensor subharness, then go to step 18.
NO - Go to step 16.
16. Check the knock sensor subharness 1P connector and the knock sensor for an open.
Is the harness OK?
YES - Go to step 17.
NO - Repair open in the knock sensor subharness, then go to step 19.
17. Replace the knock sensor.
18. Install the injector base and the intake manifold.
19. Reconnect all connectors.
20. Turn the ignition switch ON (II).
21. Reset the ECM/PCM with the HDS.
22. Do the ECM/PCM idle learn procedure.
23. Hold the engine speed at 3,000 - 4,000 rpm for at least 10 seconds.
24. Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0325 indicated?
YES - Go to step 26.
NO - Go to step 25.
25. Monitor the OBD STATUS for DTC P0325 in the DTCs MENU with the HDS.
Does the screen indicate PASSED?
YES - Troubleshooting is complete. If any other Temporary DTCs or DTCs were indicated in step 24, go to the indicated DTCs troubleshooting.
NO - If the screen indicates FAILED, check for poor connections or loose terminals at the knock sensor and the ECM/PCM, go to step 1. If the screen indicates NOT COMPLETED, go to step 23.
26. Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM.
27. Hold the engine speed at 3,000 - 4,000 rpm for at least 10 seconds.
28. Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0325 indicated?
YES - Check for poor connections or loose terminals at the knock sensor and the ECM/PCM. If the ECM/PCM was updated, substitute a known-good ECM/PCM, then go to step 27. If the ECM/PCM was substituted, go to step 1.
NO - Go to step 29.
29. Monitor the OBD STATUS for DTC P0325 in the DTCs MENU with the HDS.
Does the screen indicate PASSED?
YES - If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was substituted, replace the original ECM/PCM. If any other Temporary DTCs or DTCs were indicated in step 28, go to the indicated DTCs troubleshooting.
NO - If the screen indicates FAILED, check for poor connections or loose terminals at the knock sensor and the ECM/PCM. If the ECM/PCM was updated, substitute a known-good ECM/PCM, then go to step 27. If the ECM/PCM was substituted, go to step 1. If the screen indicates NOT COMPLETED, go to step 27.