Torque Converter Housing Disassemble & Service
Torque Converter HousingMainshaft Bearing and Oil Seal Replacement
Special Tools Required
^ Adjustable bearing puller, 25-40 mm 07736-A01000B or 07736-A01000A
^ Driver 07749-0010000
^ Attachment, 62 x 68 mm 07746-0010500
^ Attachment, 72 x 75 mm 07746-0010600
1. Remove the mainshaft bearing and oil seal with the adjustable bearing puller and a commercially available 3/8"-16 slide hammer (A).
2. Install the new mainshaft bearing until it bottoms in the housing with the driver and attachment, 62 x 68 mm.
3. Install the new oil seal flush to the housing with the driver and attachment, 72 x 75 mm.
Countershaft Bearing Replacement
Special Tools Required
^ Adjustable bearing puller, 25-40 mm 07736-A01000B or 07736-A01000A
^ Driver 07749-0010000
^ Attachment, 78 x 80 mm 07NAD-FIX40100
1. Remove the countershaft bearing from the torque converter housing with the adjustable bearing puller and a commercially available 3/8"-16 slide hammer (A).
2. Install the ATF guide plate (A) into the housing, then install the new bearing (B) in the direction shown.
3. Install the bearing (A) in the housing with the driver and attachment, 78 x 80 mm; install bearing outer race notch-cut (B) in depth (C) 0-0.03 mm (0-0.001 in.) below the housing surface (D).
Secondary Shaft Bearing Replacement
Special Tools Required
^ Adjustable bearing remover 07JAC-PH80000
^ Bearing remover shaft set, 30 mm 7936-8890300
^ Bearing remover shaft handle 07936-3710100
^ Sliding hammer weight 07741-0010201
^ Driver 07749-0010000
^ Attachment, 37 x 40 mm 07746-0010200
^ Attachment, 62 x 68 mm 07746-0010500
1. Remove the bolt, then remove the lock washer (A) and bearing set plate (B).
2. Remove the secondary shaft bearing from the torque converter housing with the adjustable bearing remover.
3. Remove the ATF guide collar from the torque converter housing.
4. Remove the 29 x 39 x 9.5 mm secondary shaft bearing from the torque converter housing with the bearing remover shaft set, 30 mm, bearing remover shaft handle, and sliding hammer weight.
5. Install the 29 x 39 x 9.5 mm bearing into the torque converter housing with the driver and attachment, 37 x 40 mm.
6. Install the new O-rings (A) on the ATF guide collar (B), then install the guide collar in the torque converter housing.
7. Install the bearing in the direction shown in the housing with the driver and attachment, 62 x 68 mm.
8. Check that the bearing groove aligns with the set plate mounting surface, then install the set plate (A) by aligning it with the bearing groove.
9. Install the new lock washer (B) and bolt, then bend the lock tab of the lock washer against the bolt head.
Intermediary Shaft Bearing Replacement
Special Tools Required
^ Adjustable bearing puller, 25-40 mm 07736-A01000B or 7736-A01000A
^ Driver 07749-0010000
^ Attachment, 52 x 55 mm 07746-0010400
1. Remove the intermediary shaft bearing from the torque converter housing with the adjustable bearing puller, 25-40 mm and a commercially available 3/8"-16 slide hammer (A).
2. Install the ATF guide plate (A), then install the new bearing (B) in the housing.
3. Drive the bearing into the housing with the driver and attachment, 52 x 55 mm.
Park Lever Shaft Bearing Replacement
Special Tools Required
^ Bearing remover shaft set, 12 mm 07936-1660101
^ Sliding hammer weight 07741-0010201
^ Driver 07749-0010000
^ Attachment, 22 x 24 mm 07746-0010800
1. Remove the park lever shaft bearing from the torque converter housing with the bearing remover shaft set, 12 mm and sliding hammer weight.
2. Install the new bearing until it bottoms in the housing with the driver and attachment, 22 x 24 mm.
