DTC Troubleshooting
DTC P0842: Short in 2nd Clutch Transmission Fluid Pressure Switch Circuit, or 2nd Clutch Transmission Fluid Pressure Switch Stuck ONNOTE:
^ Before you troubleshoot, record all freeze data and any on-board snapshot, and review General Troubleshooting Information.
^ This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
1. Clear the DTC with the HDS.
2. Check the 2nd PRESSURE SWITCH signal with the HDS in the A/T data list when not in 2nd gear.
Is the 2nd PRESSURE SWITCH OFF?
YES - Go to step 3.
NO - Go to step 6.
3. Start the engine and warm it up to normal operating temperature (the radiator fan comes on).
4. Test-drive the vehicle in 3rd gear in M for at least 2 seconds, then slow down to a stop.
5. Monitor the OBD STATUS for P0842 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate FAILED?
YES - Go to step 6.
NO - Intermittent failure, the system is OK at this time. Check the OP2SW wire for an intermittent short between the 2nd clutch transmission fluid pressure switch and the PCM. If the HDS indicates NOT COMPLETED, return to step 4 and recheck.
6. Turn the ignition switch to LOCK (0).
7. Disconnect the 2nd clutch transmission fluid pressure switch connector.
8. Turn the ignition switch to ON (II).
9. Check the 2nd PRESSURE SWITCH signal with the HDS in the A/T data list.
Is the 2nd PRESSURE SWITCH OFF?
YES - Replace the 2nd clutch transmission fluid pressure switch, then go to step 19.
NO - Go to step 10.
10. Turn the ignition switch to LOCK (0).
11. Jump the SCS line with the HDS.
12. Disconnect PCM connector C (22P).
13. Check for continuity between PCM connector terminal C11 and body ground.
Is there continuity?
YES - Repair short in the wire between PCM connector terminal C11 and the 2nd clutch transmission fluid pressure switch, then go to step 19.
NO - Go to step 14.
14. Reconnect all connectors.
15. Update the A/T software in the PCM if it does not have the latest software, or substitute a known-good PCM.
16. Test-drive the vehicle in 2nd gear in M for at least 2 seconds, then upshift to 4th gear, and drive in 4th gear for at least 2 seconds. Slow down and stop the wheels.
17. Check for DTC(s) in the DTCs/Freeze Data in A/T Mode Menu with the HDS.
Is DTC P0842 indicated?
YES - If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to step 1.
NO - Go to step 18.
18. Monitor the OBD STATUS for P0842 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate PASSED?
YES - If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM. If any other DTCs were indicated on step 17, go to the indicated DTC's troubleshooting.
NO - Check for poor connections and loose terminals at the 2nd clutch transmission fluid pressure switch and the PCM. If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, return to step 16 and recheck.
19. Clear the DTC with the HDS.
20. Test-drive the vehicle in 2nd gear in M for at least 2 seconds, then upshift to 4th gear, and drive in 4th gear for at least 2 seconds. Slow down and stop the wheels.
21. Check for DTC(s) in the DTCs/Freeze Data in A/T Mode Menu with the HDS.
Is DTC P0842 indicated?
YES - Check for poor connections and loose terminals at the 2nd clutch transmission fluid pressure switch and the PCM, then go to step 1.
NO - Go to step 22.
22. Monitor the OBD STATUS for P0842 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate PASSED?
YES - Troubleshooting is complete. If any other DTCs were indicated on step 21, go to the indicated DTC's troubleshooting.
NO - Check for poor connections and loose terminals at the 2nd clutch transmission fluid pressure switch and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, return to step 20 and recheck.