Operation CHARM: Car repair manuals for everyone.

Automatic Transmission

DTC P0815: Short in Transmission Gear Selection Switch Upshift Switch Circuit, or Transmission Gear Selection Switch Upshift Switch Stuck ON

NOTE:
^ Before you troubleshoot, record all freeze data and any on-board snapshot, and review General Troubleshooting Information.
^ This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.

1. Turn the ignition switch to ON (II).
2. Leave the shift lever in P.
3. Check the UPSHIFT SWITCH in the DATA LIST with the HDS.

Is UPSHIFT SWITCH ON?

YES - Go to step 4.

NO - Intermittent failure, the system is OK at this time. Check for intermittent short to body ground in the wire between the transmission gear selection switch and the PCM.

4. Turn the ignition switch to LOCK (0).
5. Disconnect the transmission gear selection switch/park pin switch connector.
6. Turn the ignition switch to ON (II).
7. Check the UPSHIFT SWITCH in the DATA LIST with the HDS.

Is UPSHIFT SWITCH ON?

YES - Go to step 8.

NO - Replace the transmission gear selection switch, then go to step 12.

8. Turn the ignition switch to LOCK (0).
9. Jump the SCS line with the HDS.
10. Disconnect PCM connector D (17P).
11. Check for continuity between transmission gear selection switch/park pin switch connector terminal No. 7 and body ground.





Is there continuity?

YES - Repair short to body ground in the wire between PCM connector terminal D3 and the transmission gear selection switch/park pin switch connector, then go to step 12.

NO - Go to step 20.

12. Reconnect all connectors.
13. Turn the ignition switch to ON (II).
14. Clear the DTC with the HDS.
15. Start the engine with the shift lever in P, wait for at least 10 seconds, then press the brake pedal and shift to M.
16. Push the shift lever toward upshift position (+) slowly, and return to neutral position; repeat this test at least 10 times.
17. Pull the shift lever toward downshift position (-) slowly, and return to neutral position; repeat this test at least 10 times.
18. Check for DTCs with the HDS.

Is DTC P0815 indicated?

YES - Check for intermittent short to body ground in the wire between the transmission gear selection switch and the PCM, then go to step 1.

NO - Go to step 19.

19. Monitor the OBD STATUS for P0815 in the DTCs MENU with the HDS.

Does the screen indicate PASSED?

YES - Troubleshooting is complete. If any other DTCs were indicated in step 18, go to the indicated DTC's troubleshooting.

NO - If the screen indicates FAILED, check for intermittent short to body ground in the wire between the transmission gear selection switch and the PCM, then go to step 1. If the screen indicates NOT COMPLETED, go to step 15.

20. Update the PCM if it does not have the latest software, or substitute a known-good PCM.
21. Start the engine with the shift lever in P, wait for at least 10 seconds, then press the brake pedal and shift to M.
22. Push the shift lever toward upshift position (+) slowly, and return to neutral position; repeat this test at least 10 times.
23. Pull the shift lever toward downshift position (-) slowly, and return to neutral position; repeat this test at least 10 times.
24. Check for DTCs with the HDS.

Is DTC P0815 indicated?

YES - Check for intermittent short to body ground in the wire between the transmission gear selection switch and the PCM. If the PCM was updated, substitute a known-good PCM, then go to step 21. If the PCM was substituted, go to step 1.

NO - Go to step 25.

25. Monitor the OBD STATUS for P0815 in the DTCs MENU with the HDS.

Does the screen indicate PASSED?

YES - If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM. If any other DTCs were indicated in step 24, go to the indicated DTC's troubleshooting.

NO - If the screen indicates FAILED, check for intermittent short to body ground in the wire between the transmission gear selection switch and the PCM. If the PCM was updated, substitute a known-good PCM, then go to step 21. If the PCM was substituted, go to step 1. If the screen indicates NOT COMPLETED, go to step 21.