Operation CHARM: Car repair manuals for everyone.

DTC Troubleshooting




DTC Troubleshooting: P1454 (91-5), P2422 (117-3)

DTC P1454:

FTP Sensor Circuit Range/Performance Problem

DTC P2422:

EVAP Canister Vent Shut Valve Stuck Closed

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information Initial Inspection and Diagnostic Overview.

1. Turn the ignition switch to ON (II).

2. Clear the DTC with the HDS.

3. Turn the ignition switch to LOCK (0).

4. Remove the fuel fill cap, and wait 1 minute.

5. Turn the ignition switch to ON (II).

6. Check the FTP SENSOR in the DATA LIST with the HDS.

Is it between -0.67 and 0.67 kPa (-0.2 and 0.2 inHg, -5 and 5 mmHg), or 2.4 and 2.6 V?

YES -

Go to step 7.

NO -

Go to step 18.

7. Reinstall the fuel fill cap.

8. Clear the DTC with the HDS.

9. Start the engine. Hold the engine speed at 3,000 rpm without load (in P or N) until the radiator fan comes on, then let it idle.

10. Monitor the OBD STATUS for DTC P1454 in the DTCs MENU with the HDS.

Does the HDS indicate FAILED?

YES -

Go to step 11.

NO -

If the HDS indicates PASSED, intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the FTP sensor, the EVAP canister vent shut valve, and the PCM. Also check for a blockage in the vent hoses and the drain joint. If the HDS indicates NOT COMPLETED, keep idling until a result comes on.

11. Clear the DTC with the HDS.

12. Turn the ignition switch to LOCK (0).

13. Remove the EVAP canister vent shut valve from the EVAP canister Service and Repair.

14. Connect the 2P connector to the EVAP canister vent shut valve.

15. Turn the ignition switch to ON (II).

16. Select EVAP CVS ON in the INSPECTION MENU with the HDS.

17. Check the EVAP canister vent shut valve (A) operation.





Does the valve operate?

YES -

Check for a blockage in the EVAP canister, the vent hoses, and the drain joint, then install the EVAP canister vent shut valve, and go to step 26.

NO -

Replace the EVAP canister vent shut valve Service and Repair, then go to step 26.

18. Remove the trunk front trim panel Interior Trim Removal / Installation - Trunk Area.

19. Remove the access panel from the floor Service and Repair.

20. Disconnect the vent tube (A) from the FTP sensor (B).





21. Check the FTP SENSOR in the DATA LIST with the HDS.

Is it between -0.67 kPa and 0.67 kPa (-0.2 and 0.2 inHg, -5 and 5 mmHg), or 2.4 and 2.6 V?

YES -

Check for a blockage in the FTP sensor vent tube, clear the blockage and reconnect the vent tube, then go to step 26.

NO -

Go to step 22.

22. Turn the ignition switch to LOCK (0).

23. Remove the FTP sensor (A) from the EVAP canister with its connector connected.






24. Turn the ignition switch to ON (II).

25. Check the FTP SENSOR in the DATA LIST with the HDS.

Is it between -0.67 kPa and 0.67 kPa (-0.2 and 0.2 inHg, -5 and 5 mmHg), or 2.4 and 2.6 V?

YES -

Check for debris or clogging at the EVAP canister and the FTP sensor port, then go to step 26.

NO -

Replace the FTP sensor Service and Repair, then go to step 26.

26. Turn the ignition switch to ON (II).

27. Reset the PCM with the HDS.

28. Do the PCM idle learn procedure PCM Idle Learn Procedure.

29. Start the engine. Hold the engine speed at 3,000 rpm without load (in P or N) until the radiator fan comes on, then let it idle.

30. Check for Pending or Confirmed DTCs with the HDS.

Is DTC P1454 and/or P2422 indicated?

YES -

Check for poor connections or loose terminals at the FTP sensor, the EVAP canister vent shut valve, and the PCM, then go to step 1.

NO -

Go to step 31.

31. Monitor the OBD STATUS for DTC P1454 and/or P2422 in the DTCs MENU with the HDS.

Does the HDS indicate PASSED?

YES -

Troubleshooting is complete. If any other Pending or Confirmed DTCs were indicated in step 30, go to the indicated DTC's troubleshooting.�

NO -

If the HDS indicates FAILED, check for poor connections or loose terminals at the FTP sensor, the EVAP canister vent shut valve, and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, keep idling until a result comes on.