Operation CHARM: Car repair manuals for everyone.
Home >> Acura >> 2011 >> TL AWD V6-3.7L >> Repair and Diagnosis >> Engine, Cooling and Exhaust >> Engine >> Drive Belts, Mounts, Brackets and Accessories >> Engine Mount >> Testing and Inspection >> Engine Mount Control System Troubleshooting (M/T)

Engine Mount Control System Troubleshooting (M/T)




Engine Mount Control System Troubleshooting

Special Tools Required

- Vacuum Pump/Gauge, 0-30 inHg Snap-on YA4000A or equivalent, commercially available

M/T model

NOTE:

- Check the vacuum hoses and lines for damage and proper connections before troubleshooting.
- Check the liquid filled engine mount for damage. The rubber mount should have dimples in it. This is normal. If the internal bladder ruptures, the rubber mount will look like it is bulging. Replace it Front Engine Mount Removal/Installation.

Follow this procedure if the engine vibrates excessively when idling.

1. Remove the engine compartment cover Service and Repair.

2. Start the engine, and let it idle.

3. Raise the engine speed from idling to 2,000 rpm.

4. Check the MOUNT CTRL SOL in the PGM-FI DATA LIST with the HDS.

Is ON indicated at idling and OFF indicated at 2,000 rpm?

YES -

Go to step 5.

NO -

Update the ECM if it does not have the latest software ECM/PCM Update, or substitute a known-good ECM, then recheck. If the engine mount control system works properly, and the ECM was updated, the troubleshooting is complete. If the ECM was substituted, replace the original ECM Service and Repair.�

5. Press the engine start/stop button to select the OFF mode.

6. Disconnect the engine mount control solenoid valve 2P connector from the engine mount control solenoid valve.

7. Press the engine start/stop button to select the ON mode.

8. Measure the voltage between engine mount control solenoid valve 2P connector terminal No. 2 and body ground.





Is there battery voltage?

YES -

Go to step 9.

NO -

Repair an open in the wire between engine mount control solenoid valve 2P connector terminal No. 2 and No. 13 (15 A) fuse in the driver's under-dash fuse/relay box.�

9. Start the engine, and let it idle.

10. Measure the voltage between engine mount control solenoid valve 2P connector terminals No. 1 and No. 2, with the engine at idle.





Is there battery voltage?

YES -

Go to step 11.

NO -

Repair an open in the wire between ECM connector terminal A12 and engine mount control solenoid valve 2P connector terminal No. 1. If the wire is OK, update the ECM if it does not have the latest software ECM/PCM Update, or substitute a known-good ECM, and recheck. If the engine mount control system works properly, and the ECM was updated, the troubleshooting is complete. If the ECM was substituted, replace the original ECM Service and Repair.�

11. Raise the engine speed above 2,000 rpm.

12. Measure the voltage between engine mount control solenoid valve 2P connector terminals No. 1 and No. 2.





Is there battery voltage?

YES -

Repair a short to body ground in the wire between ECM connector terminal A12 and the engine mount control solenoid valve. If the wire is OK, update the ECM if it does not have the latest software ECM/PCM Update, or substitute a known-good ECM, and recheck. If the engine mount control system works properly, and the ECM was updated, the troubleshooting is complete. If the ECM was substituted, replace the original ECM Service and Repair.�

NO -

Reconnect the engine mount control solenoid valve 2P connector, then go to step 14.

13. Press the engine start/stop button to select the OFF mode.

14. Disconnect the vacuum hose (A) from the engine mount control solenoid valve (B), and connect a vacuum pump/gauge, 0-30 inHg, to the vacuum hose. Apply about 20 inHg of vacuum, and wait for 20 seconds.





Does the engine mount hold vacuum?

YES -

Reconnect the vacuum hose, then go to step 16.

NO -

Reconnect the vacuum hose, then go to step 15.

15. Disconnect the vacuum hose (A) from the two way valve, and connect a vacuum pump/gauge to the hose. Apply about 20 inHg vacuum, and wait 20 seconds.





Does the engine mount hold vacuum?

YES -

Repair the vacuum hose (B) between the engine mount control solenoid valve and the two way valve.�

NO -

The vacuum hose or the front engine mount has a vacuum leak. Repair as needed.�

16. Disconnect the vacuum hose (A) from the two way valve, then connect the vacuum pump/gauge to the vacuum hose.






17. Start the engine and let it idle, then apply vacuum to the mount.

Is there a noticeable change in idle smoothness with and without vacuum applied?

YES -

Reconnect the vacuum hose to the two way valve, then go to step 18.

NO -

Replace the front engine mount Front Engine Mount Removal/Installation.�

18. Disconnect the vacuum hose (A) from the engine mount control solenoid valve (B), then connect a vacuum pump/gauge to the engine mount control solenoid valve.





Is there manifold vacuum at idle, and a decrease in manifold vacuum when you raise the engine speed above 2,000 rpm?

YES -

The system is OK.�

NO -

Repair the vacuum hose (C) between the intake manifold and the engine mount control solenoid valve. If the vacuum hose is OK, replace the engine mount control solenoid valve.�

pro multis · About Operation CHARM