DTC Troubleshooting
DTC Troubleshooting: P0967 (23)
DTC P0967:
Problem in A/T Clutch Pressure Control Solenoid Valve B
NOTE:
- Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review General Troubleshooting Information Reading and Clearing Diagnostic Trouble Codes.
- This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
1. Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.
2. Clear the DTC with the HDS.
3. Start the engine, and wait for at least 1 second.
4. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0967 indicated?
YES -
Go to step 8.
NO -
Go to step 5.
5. Select Clutch Pressure Control (Linear) Solenoid Valve B in the Miscellaneous Test Menu, and test A/T clutch pressure control solenoid valve B with the HDS.
Does the HDS indicate NORMAL?
YES -
Go to step 6.
NO -
Go to step 8.
6. In the Clutch Pressure Control Solenoid Valve Control menu, set A/T Clutch Pressure Control Solenoid Valve B at 0.2 A.
7. Monitor the OBD status for P0967 in the DTCs MENU with the HDS.
Does the HDS indicate FAILED?
YES -
Go to step 8.
NO -
If the HDS indicates PASSED, intermittent failure, the system is OK at this time. Check for poor connections or loose terminals between A/T clutch pressure control solenoid valve B and the PCM. If the HDS indicates NOT COMPLETED, go to step 5.
8. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
9. Disconnect the A/T clutch pressure control solenoid valve B connector.
10. Measure the resistance between A/T clutch pressure control solenoid valve B connector terminals No. 1 and No. 2.
Is there 3-10 Ohms?
YES -
Go to step 14.
NO -
Replace A/T clutch pressure control solenoid valve B A/T Clutch Pressure Control Solenoid Valve A and B Replacement, then go to step 11.
11. Start the engine, and wait for at least 1 second.
12. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0967 indicated?
YES -
Check for poor connections or loose terminals between A/T clutch pressure control solenoid valve B and the PCM, then go to step 1.
NO -
Go to step 13.
13. Monitor the OBD status for P0967 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
Troubleshooting is complete. If any other Pending or Confirmed DTCs were indicated in step 12, go to the indicated DTC's troubleshooting.�
NO -
If the HDS indicates FAILED, check for poor connections or loose terminals between A/T clutch pressure control solenoid valve B and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, go to step 11.
14. Reconnect all connectors.
15. Update the PCM if it does not have the latest software ECM/PCM Update, or substitute a known-good PCM.
16. Start the engine, and wait for at least 1 second.
17. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0967 indicated?
YES -
Check for poor connections or loose terminals between A/T clutch pressure control solenoid valve B and the PCM. If the PCM was updated, substitute a known-good PCM, then go to step 16. If the PCM was substituted, go to step 1.
NO -
Go to step 18.
18. Monitor the OBD status for P0967 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM Service and Repair. If any other Pending or Confirmed DTCs were indicated in step 17, go to the indicated DTC's troubleshooting.�
NO -
If the HDS indicates FAILED, check for poor connections or loose terminals between A/T clutch pressure control solenoid valve B and the PCM. If the PCM was updated, substitute a known-good PCM, then go to step 16. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, go to step 16.