Operation CHARM: Car repair manuals for everyone.
Home >> Acura >> 2011 >> TSX Sedan V6-3.5L >> Repair and Diagnosis >> Accessories and Optional Equipment >> Radio, Stereo, and Compact Disc >> Testing and Inspection >> Initial Inspection and Diagnostic Overview >> Audio System Self-Diagnostic Function

Audio System Self-Diagnostic Function




Audio System Self-Diagnostic Function

The audio system has a self-diagnostic function.

NOTE:

- Not all self-diagnostic functions appear on all models.
- There may be other self-diagnostic functions that are for factory use only.

How to Obtain the Audio Unit Serial Number

NOTE: This procedure can only be done after the power has been disconnected and reconnected to the audio unit, and the audio unit displays CODE when the audio unit is turned on.

1. Turn the ignition switch to ON (II).

2. Make sure the audio system is turned off.

3. Push and hold the preset No. 1 and No. 6 buttons.

4. While holding the buttons, push the VOLUME/POWER knob to on.

5. Release the buttons, and the self-diagnosis begins.






6. The display shows an 8 digit serial number.





7. Use all 8 numbers as the serial number when using the Interactive Network (in) to retrieve the 5 digit anti-theft code.

8. To end the self-diagnostic function, turn the audio system off, or turn the ignition switch to LOCK (0).

How to Use the Audio System Self-Diagnostic Function

1. Turn the ignition switch to ON (II).

2. Make sure the audio system is turned off.

3. Push and hold the preset No. 1 and No. 6 buttons.

4. While holding the buttons, push the VOLUME/POWER knob to on.

5. Release the buttons, and the self-diagnosis begins.






6. When you are in the self-diagnostic mode, pressing a preset button starts the diagnostic mode that is assigned to that preset button.

NOTE: Any other diagnostic screens shown are for factory use only.

No. 2 button

Audio button, knob, and audio remote switch detection: Allows individual manual selection of all audio panel knobs, buttons, and remote switches to verify if they are functional. When properly detected, the selected knob, button, or audio remote switch name and/or value is displayed. To exit this mode, go to step 7. Once you exit this test, you must start again at step 1.

No. 3 button

Entire LCD lighting/light-out mode: Turns on/off the entire LCD to show the presence (LCD stuck on) or absence (LCD dead) of an LCD segment.

No. 4 button

Duty indication mode (for the Illumination dim): Indicates the duty for the Illumination dim when the dash lights are on.

No. 5 button

Vehicle speed pulse (VSP) indication mode: Indicates the vehicle speed pulse.

FM/AM or FM button (Push and hold 5 sec)

Reception level indication mode: Indicates the reception level (dB). When entering the reception level check mode, the A.SEL button turn the AM/FM antenna amplifier on and off.

7. The self-diagnostic function ends when you turn the audio unit off, or turn the ignition switch to LOCK (0).

Display Specifications

Entire LCD lighting/lights-outs mode (press No. 3 button)

This diagnostic screen checks for segments that may be dead (off) or stuck on.

All the display segments should be on. If any segments are dead (off), replace the audio-navigation switch panel Audio-Navigation Switch Panel Removal/Installation or audio-HVAC display unit Audio-HVAC Display Unit Removal/Installation. With all the segments on, press the No. 3 button a second time. The entire display must turn black. If any segments are stuck on, replace the audio-navigation switch panel Audio-Navigation Switch Panel Removal/Installation or audio-HVAC display unit Audio-HVAC Display Unit Removal/Installation.

Entire LCD lighting mode





Entire LCD lights-outs mode





Reception level indication (Push and hold 5 sec FM/AM or FM button)

This diagnostic screen checks the radio reception level. This level then can used in the diagnosis of radio reception quality. The reception level is displayed in decibels (dB).

Preparation:

- Park the vehicle outdoors in a location with good radio reception.
- Tune to a powerful local FM radio station, then write down the radio station number.
- Tune to a powerful local AM radio station, then write down the radio station number.

1. Enter the reception level indication mode in the self-diagnostic function. The AM/FM antenna amplifier is on and the character (A) is not displayed in the audio display.






2. Tune to the FM radio station you wrote down in preparation using the TUNE button (with ELS audio) or selector knob (with premium audio), and note the decibel level (B) of that station.

3. Press and release the A.SEL button to turn the AM/FM antenna amplifier off (A is now displayed in the audio display).

4. Note the decibel level of that station.

5. Press and release the A.SEL button to turn the AM/FM antenna amplifier back on (A is not displayed in the audio display).

6. Press and hold the FM/AM button (with ELS audio) or AM button (with premium audio) for more than 5 seconds to enter the AM reception mode.

7. Tune to the AM radio station you wrote down in preparation using the TUNE button (with ELS audio) or selector knob (with premium audio), and note the decibel level of that station.

8. Press and release the A.SEL button to turn the antenna amplifier off.

9. Note the decibel level of that station.

10. Press and release the A.SEL button to turn the AM/FM antenna amplifier back on.

11. Turn the ignition switch to LOCK (0), or audio system off to exit the test mode.

12. Compare your results to a known-good vehicle, (make sure it is the same year and trim level) in the same location and direction, and under the same environmental conditions.

Speaker Check Mode

NOTE:

- Not all self-diagnostic functions appear on all models.
- There may be other self-diagnostic functions that are for factory use only.
- In some cases, you may not be able to enter a mode even if the designated button is pressed. In that case, try again.

1. Turn the ignition switch to ON (II).

2. Make sure the audio system is turned off.

3. Push and hold the preset No. 1 and No. 3 buttons.

4. While holding the buttons, push the VOLUME/POWER knob to on.

5. Release the buttons and the speaker check mode begins. the FM default frequency should sound from one speaker.

6. Each time you press the SKIP button, the test moves to the next speaker in the order listed in the table.

NOTE: Adjust the volume level to a comfortable level.






Display Specifications (with ELS audio)










Display Specifications (with premium audio)













7. The speaker check mode ends when you turn the audio unit off, or turn the ignition switch to LOCK (0).

How to Check the ANC/Active Sound Control System in this Check Mode

1. Turn the ignition switch to ON (II).

2. Make sure the audio system is turned off.

3. Push and hold the preset No. 1 and No. 6 buttons.

4. While holding the buttons, push the VOLUME/POWER knob to on.

5. Release the buttons, and the self-diagnosis begins.






6. With the engine stopped, and while in DIAG mode, turn the ANC ON to OFF by pressing the No. 1 button. A low frequency hum (50 Hz) should sound for about a minute.

- If the hum does not sound, check for an open in the wire between the ANC/active sound control unit and the audio-navigation unit or audio unit.
- If the hum sounds for a second, check for an open in the wire between ANC/active sound control unit and the microphone.

NOTE: The ANC/active sound control system is cancelled when any door is opened.

7. The self-diagnostic function ends when the audio system is turned off, or turn the ignition switch to LOCK (0).

XM Self-Diagnosis

NOTE: This diagnostic screen checks the audio unit's XM radio reception level. To check the XM reception, do the following:

1. Turn the ignition switch to ON (II).

2. Select XM1 mode.

3. Turn off the audio system.

4. Push and hold the preset No. 3 and No. 6 buttons.

5. While holding the buttons, push the VOLUME/POWER knob to on.

6. Continue holding the buttons for about 5 seconds, then release the buttons.

7. Press and release preset No. 1 button to read the error code.










8. To end the XM self-diagnosis, turn the ignition switch to LOCK (0).

XM Signal Reception Level Indication Mode

NOTE: When you receive any XM complaint, do the XM self-diagnosis to check for any XM error codes first. If there are no XM codes, check the XM signal reception level. To check the XM signal reception, do the following:

1. Turn the ignition switch to ON (II).

2. Select XM2 mode.

3. Turn off the audio system.

4. Push and hold the preset No. 3 and No. 6 buttons.

5. While holding the buttons, push the VOLUME/POWER knob to on.

6. Continue holding the buttons for about 5 seconds, then release the buttons.

7. Press and release preset No. 1 button to read the XM signal reception.






8. To end the XM self-diagnosis, turn the ignition switch to LOCK (0).

pro multis · About Operation CHARM