A/T System Description - Electronic Control System
A/T System Description - Electronic Control System
Electronic Control System
Electronic Control
The electronic control system consists of the PCM, sensors, and solenoid valves.
Function Diagram
The PCM receives input signals from sensors, switches, and other control units, processes data, and outputs signals for the engine control system and the A/T control system. The A/T control system includes shift control, grade logic control, clutch pressure control, and lock-up control. The PCM switches the shift solenoid valves and the A/T clutch pressure control solenoid valves ON and OFF in a specific sequence to control gear selection and torque converter clutch lock-up.
Shift Control
The PCM instantly determines which gear should be selected by various inputs from sensors and switches, and it actuates shift solenoid valves A, B, C, D, and E to control gear selection.
The PCM turns shift solenoid valves A, B, C, D, and E ON and OFF to control gear selection.
All shift solenoid valves are normally closed (ON-OPEN/OFF-CLOSED). The shift solenoid valve port opens to allow ATF to pass through when the PCM turns it ON, and the port closes, blocking fluid flow when turned OFF. The combination of driving signals to shift solenoid valves A, B, C, D, and E for each gear are in the following table.
Electronic Control System (cont'd)
Shift Control - Grade Logic
The grade logic control system has been included to improve shifting in D, and in S with automatic shift mode. The PCM compares actual driving conditions with programmed driving conditions, based on the input from the accelerator pedal position sensor, the engine coolant temperature sensor, the barometric pressure sensor, the brake pedal position switch, the output shaft (countershaft) speed sensor, the throttle position sensor, and the transmission range switch, to improve shifting control while the vehicle is ascending or descending a slope.
Grade Logic Control: Ascending Control
When the PCM determines that the vehicle is climbing a hill in D, and in S with automatic shift mode, the PCM extends the engagement area of 2nd, 3rd, and 4th gears to prevent the transmission from frequently shifting between 2nd and 3rd gears, between 3rd and 4th gears, and between 4th and 5th gears, so the vehicle can run smoothly and have more power when needed.
Grade Logic Control: Descending Control
When the PCM determines that the vehicle is going down a hill in D, and in S with automatic shift mode, the upshift speed from 4th to 5th gear, from 3rd to 4th gear, and from 2nd to 3rd gear (when the throttle is closed) becomes higher than the set speed for flat road driving to extend 4th gear, 3rd gear, and 2nd gear driving conditions or modes. This, in combination with engine braking from the deceleration lock-up, achieves smooth driving when the vehicle is descending. There are three descending modes stored in the PCM with different 4th gear, 3rd gear, and 2nd gear driving conditions or modes based on the steepness of the grade. When the vehicle is in 5th gear or 4th gear, and the vehicle is decelerating while applying the brakes on a steep hill, the transmission will downshift to lower gear. When you accelerate, the transmission will then return to a higher gear.
Electronic Control System (cont'd)
Shift-Hold Control
When driving on winding roads, if the throttle is suddenly released and the brakes are applied, as is the case when decelerating at the entrance of a curve, shift-hold control keeps the transmission in its current (lower) gear as it negotiates the corner and accelerates out.
When the vehicle is driven aggressively on a winding road, the PCM extends the engagement time of 3rd gear and 4th gear to prevent the transmission from frequently shifting between 3rd, 4th, and 5th gears.
The PCM monitors the change in the vehicle speed and throttle over time. When these values exceed those for normal driving conditions, the upshift from 3rd to 4th gear and 4th to 5th gear are delayed. This gives more control over power, and the engine braking. The transmission resumes the normal upshift pattern after the PCM determines that normal driving has resumed.
Shift Control - Manual Shift Mode
The transmission is provided with a D-paddle shift mode in D, and with a sequential SportShift mode in S. Either mode can be activated by pressing the paddle shifter + (upshift switch) or the paddle shifter - (downshift switch) while driving with the shift lever in D and S.
D-Paddle Shift Mode
To engage the D-paddle shift mode, press back on either of the steering wheel mounted paddle shifters while driving in the D position. In this mode, the transmission can downshift by pressing the paddle shifter -, or upshift by pressing the paddle shifter +. There are five speeds, so each time the transmission is shifted using the paddle shifters, the shift indicator in the gauge control module displays the current position. The display turns off when the transmission upshifts or downshifts automatically.
The transmission stays in 5th gear if the paddle shifter + is pressed when driving in 5th gear, and the shift indicator displays "5" for 2 seconds, then goes off. The transmission stays in 1st gear if the paddle shifter - is pressed when driving in 1st gear, and the shift indicator displays "1" for 2 seconds, then goes off.
The transmission stays in the current gear and does not upshift to the next higher gear if the paddle shifter + is pressed while driving below the minimum allowable speed, and the shift indicator blinks the number of the next higher gear several times, then returns to the number of the current gear.
Electronic Control System (cont'd)
S Position Automatic Shift Mode and Sequential SportShift Mode
The S position has two shifting modes; the automatic shift mode and the sequential SportShift mode. In the S position automatic shift mode, the transmission upshifts and downshifts automatically from 1st through 4th gear, if the paddle shifters are not pressed. In the automatic shift mode, the shift indicator and the M indicator in the gauge control module do not come on.
When the paddle shifter + (upshift switch) or the paddle shifter - (downshift switch) is pressed, the automatic shift mode is canceled and the sequential SportShift mode comes into operation. The shift indicator displays the number of the selected gear, and the M indicator comes on. In the sequential SportShift mode, the driver can shift up and down manually from 1st through 5th gear by using the paddle shifters, much like a manual transmission. The paddle shifters are installed on the back of the steering wheel, and the driver can shift gears by pressing the paddle shifters without taking either hand off the steering wheel.
In the sequential SportShift mode, the transmission must be shifted up and down by pressing the paddle shifters.
However, if the vehicle is coasting at a speed that would cause the engine to over-rev by downshifting, the transmission will not shift when the paddle shifter - is pressed. The shift indicator blinks the number of the selected gear position several times, then returns to the current gear. If the vehicle speed reaches an appropriate speed while the shift indicator is blinking, the transmission downshifts and the shift indicator displays the selected gear. Likewise, if the vehicle speed is below an appropriate speed to upshift when the paddle shifter + is pressed, the transmission will not shift. The shift indicator blinks the number of the selected gear several times, and then returns to the number of the current gear. If the vehicle speed reaches an appropriate upshift speed while the shift indicator is blinking, the transmission upshifts and the shift indicator displays the selected gear.
This mode has automatic downshifting areas so the vehicle can run smoothly with more power to cope with upcoming acceleration. When coasting in 5th gear or 4th gear, the transmission downshifts to the next lower gear if the vehicle slows down to the programmed speed, or by pressing the brake pedal.
When the transmission decelerates to a stop, the transmission shifts to 1st gear automatically. The transmission can be shifted to 2nd gear by pressing the paddle shifter + while the vehicle is stopped, and the vehicle can start off in 2nd gear.
The sequential SportShift mode is canceled when moving the shift lever to any position other than S.
Clutch Pressure Control
The PCM actuates A/T clutch pressure control solenoid valves A, B, and C to control the clutch pressure. When shifting between lower and higher gears, the clutch pressure regulated by A/T clutch pressure control solenoid valves A, B, and C engages and disengages the clutch smoothly.
The PCM receives input signals from the various sensors and switches, processes data, and outputs current to A/T clutch pressure control solenoid valves A, B, and C.
Electronic Control System (cont'd)
Lock-Up Control
Shift solenoid valve E controls the hydraulic pressure to switch the lock-up shift valve and lock-up ON and OFF. When the PCM actuates shift solenoid valve E and A/T clutch pressure control solenoid valve A, lock-up starts. A/T clutch pressure control solenoid valve A regulates and applies hydraulic pressure to the lock-up control valve to control the amount of the lock-up.
The lock-up mechanism operates in D (2nd, 3rd, 4th, and 5th gears), and in S with sequential SportShift mode (2nd, 3rd, 4th, and 5th gears) and automatic shift mode (2nd, 3rd, and 4th gears).
Self-Diagnosis
If the PCM detects the failure of a signal from a sensor, a switch, a solenoid valve, or from another control unit, it stores a Pending or Confirmed DTCs. Depending on the failure, a Confirmed DTC is stored in either the first or the second drive cycle. When a DTC is stored, the PCM blinks the D indicator and/or turns on the malfunction indicator lamp (MIL) by a signal sent to the gauge control module via F-CAN.
- One Drive Cycle Detection Method:
When an abnormality occurs in the signal from a sensor, a switch, a solenoid valve, or from another control unit, the PCM stores a Confirmed DTC for the failure and blinks the D indicator and/or turns on the MIL immediately.
- Two Drive Cycle Detection Method:
When an abnormality occurs in the signal from a sensor, a switch, a solenoid valve, or from another control unit in the first drive cycle, the PCM stores a Pending DTC. The D indicator and the MIL do not turn on at this time. If the failure continues in the second drive cycle, the PCM stores a Confirmed DTC and blinks the D indicator and/or turns on the MIL.
Fail-Safe Function
When an abnormality occurs in the signal from a sensor, a switch, a solenoid valve, or from another control unit, the PCM ignores it and substitutes a pre-programmed value for that signal to allow the automatic transmission to continue operating. This causes a DTC to be stored and the D indicator to blink and/or the MIL to come on. The transmission may not shift normally during fail-safe operation. Do not run the test-driving diagnosis when the MIL is ON, or the D indicator is blinking.
Electronic Control System (cont'd)
PCM A/T Control System Electrical Connections
PCM A/T Control System Inputs and Outputs at PCM Connector A (square) (49P)
Electronic Control System (cont'd)
PCM A/T Control System Inputs and Outputs at PCM Connector B (triangle) (49P)
PCM A/T Control System Inputs and Outputs at PCM Connector B (triangle) (49P)
Electronic Control System (cont'd)
PCM A/T Control System Inputs and Outputs at PCM Connector C (circle) (49P)