Manufacturer Code Charts: 47
Adaptive Cruise Control (ACC) DTC Troubleshooting: 47
DTC 47:
Cal FR Brake System Malfunction
NOTE: In this troubleshooting, you will operate the ADAPTIVE CRUISE CONTROL (ACC) BRAKE (brake actuator 3) continuously four or five times using the FUNCTION TEST with the HDS. During this operation, the VSA modulator-control unit may stop working. This means the VSA modulator-control unit has shut down to protect the system from overheating during continuous operation.
If the VSA modulator-control unit stops working, wait for a few minutes until the VSA modulator-control unit cools down, then restart the troubleshooting.
1. Check for VSA system DTCs with the HDS Reading and Clearing Diagnostic Trouble Codes.
Are any DTCs indicated?
YES -
Troubleshoot the indicated VSA system DTC(s).
NO -
Go to step 2.
2. Start the engine, and press the MAIN switch ON.
3. Clear the DTCs with the HDS.
4. Select ADAPTIVE CRUISE CONTROL (ACC) from the DRIVING SUPPORT menu, then enter the FUNCTION TEST.
5. Activate BRAKE ACTUATOR 3 from the FUNCTION TEST menu.
6. Watch the ACC indicator.
Does the ACC indicator (amber) come on?
YES -
Go to step 10.
NO -
Go to step 7.
7. Activate BRAKE ACTUATOR 3 again.
8. While the brake actuator is operating, press the brake pedal.
9. Watch the ACC indicator.
Does the ACC indicator (amber) come on?
YES -
Go to step 10.
NO -
Intermittent failure, the system is OK at this time. Check for loose or poor connections.
10. Check for DTCs with the HDS.
Is DTC 47 indicated?
YES -
Go to step 11.
NO -
Troubleshoot the indicated DTC(s).
11. Press the engine start/stop button to select the OFF mode.
12. Press the brake pedal several times, and check the brake pedal travel.
Does the brake pedal sink?
YES -
Inspect the master cylinder Testing and Inspection.
NO -
Go to step 13.
13. Check for brake fluid leaks Testing and Inspection.
Are there any brake fluid leaks?
YES -
Repair the brake fluid leak.
NO -
Go to step 14.
14. Start the engine.
15. Check the brake switch signal (BRAKE SW (N.O.)) with the HDS.
Does the indication show ON when the brake pedal is pressed, and show OFF when the brake pedal is released?
YES -
Go to step 17.
NO -
Go to step 16.
16. Check for DTCs with the HDS.
Is DTC 60, 110, or 111 indicated?
YES -
Troubleshoot the indicated DTC(s).
NO -
Troubleshoot the brake pedal position switch signal circuit Brake Pedal Position Switch Signal Circuit Troubleshooting.
17. Press the MAIN switch ON.
18. Clear the DTCs with the HDS.
19. Select ADAPTIVE CRUISE CONTROL (ACC) from the DRIVING SUPPORT menu, then enter the FUNCTION TEST.
20. Activate BRAKE ACTUATOR 3 from the FUNCTION TEST.
21. Check for DTCs with the HDS.
Is DTC 47 indicated?
YES -
Check the brake fluid pressure sensor for proper installation or leaks Service and Repair. If OK, go to step 22.
NO -
Troubleshoot the indicated DTC(s). If there are no DTCs, the system is OK at this time.
22. Without the brake pedal pressed, check the right front brake fluid pressure voltage (RF BRAKE P) with the HDS.
Is there about 0.5 V?
YES -
Go to step 23.
NO -
Go to step 26.
23. Test the brake booster Testing and Inspection.
24. Start the engine, then press the brake pedal with about 314 N (32.0 kgf, 70.6 lbf) pressure.
25. Check the right front brake fluid pressure voltage (RF BRAKE P) with the HDS.
Is there about 2.5 V?
YES -
Check for loose or poor connections. If OK, update the ACC unit Testing and Inspection, then recheck. If the ACC unit was already updated, replace the ACC unit Service and Repair.
NO -
Go to step 26.
26. Check for DTCs with the HDS.
Is DTC 47 indicated?
YES -
Check for loose or poor connections. If OK, update the ACC unit Testing and Inspection, then recheck. If the ACC unit was already updated, replace the ACC unit Service and Repair.
NO -
Troubleshoot the indicated DTC(s). If there are no DTCs, the system is OK at this time.