DTC Troubleshooting
DTC Troubleshooting: P0135, P0155
DTC P0135:
Rear A/F Sensor (Bank 1, Sensor 1) Heater Circuit Malfunction
DTC P0155:
Front A/F Sensor (Bank 2, Sensor 1) Heater Circuit Malfunction
NOTE:
- Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information Initial Inspection and Diagnostic Overview.
- Information marked with an asterisk (*) applies to the front bank (Bank 2).
1. Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.
2. Clear the DTC with the HDS.
3. Start the engine.
4. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0135 and/or P0155* indicated?
YES -
Go to step 5.
NO -
Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at A/F sensor (Sensor 1), the PGM-FI subrelay, and the PCM.
5. Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode.
6. Check the No. 14 FI SUB (15 A) fuse in the under-hood fuse/relay box.
Is the fuse OK?
YES -
Go to step 7.
NO -
Go to step 20.
7. Remove the PGM-FI subrelay (A) from the under-hood fuse/relay box.
8. Test the PGM-FI subrelay Testing and Inspection.
Is the relay OK?
YES -
Go to step 9.
NO -
Replace the PGM-FI subrelay, then go to step 26.
9. Disconnect the A/F sensor (Sensor 1) 6P connector.
10. At the sensor side, measure the resistance between A/F sensor (Sensor 1) 6P connector terminals No. 1 and No. 2.
Is there 2.5-4.0 Ohms at the room temperature?
YES -
Go to step 11.
NO -
Go to step 25.
11. At the sensor side, check for continuity between each terminal of at the A/F sensor (Sensor 1) 6P connector and body ground.
Is there continuity to body ground at any terminal?
YES -
Go to step 25.
NO -
Go to step 12.
12. At the sensor side, check for continuity between A/F sensor (Sensor 1) 6P connector terminal No. 1 and each of the other terminals in the connectors individually.
Is there continuity?
YES -
Go to step 25.
NO -
Go to step 13.
13. Jump the SCS line with the HDS.
14. Disconnect PCM connector C (49P).
15. Check for continuity between PCM connector terminal C6 (C8)* and body ground.
Is there continuity?
YES -
Repair a short in the wire between the PCM (C6 (C8)*) and the A/F sensor (Sensor 1), then go to step 26.
NO -
Go to step 16.
16. Check for continuity between A/F sensor (Sensor 1) 6P connector terminal No. 2 and PCM connector terminal C6 (C8)*.
Is there continuity?
YES -
Go to step 17.
NO -
Repair an open in the wire between the PCM (C6 (C8)*) and the A/F sensor (Sensor 1), then go to step 26.
17. Check for continuity between A/F sensor (Sensor 1) 6P connector terminal No. 1 and PGM-FI subrelay 4P connector terminal No. 2.
Is there continuity?
YES -
Go to step 18.
NO -
Repair an open in the wire between the A/F sensor (Sensor 1) and the PGM-FI subrelay, then go to step 26.
18. Disconnect PCM connector A (49P).
19. Check for continuity between PGM-FI subrelay 4P connector terminal No. 3 and PCM connector terminal A40.
Is there continuity?
YES -
Go to step 32.
NO -
Repair an open in the wire between the PGM-FI subrelay and the PCM (A40), then go to step 26.
20. Remove the PGM-FI subrelay (A) from the under-hood fuse/relay box.
21. Disconnect the front and rear A/F sensor (Sensor 1) 6P connectors.
22. Disconnect the front and rear secondary HO2S (Sensor 2) 4P connectors.
23. Disconnect the EVAP canister vent shut valve 2P connector.
24. Check for continuity between A/F sensor (Sensor 1) 6P connector terminal No. 1 and body ground.
Is there continuity?
YES -
Repair a short in the wire between the PGM-FI subrelay and the A/F sensor (Sensor 1), then go to step 26.
NO -
Check the under-hood fuse/relay box, and replace it if needed Under-Hood Fuse/Relay Box Removal and Installation. Also replace the No. 14 FI SUB (15 A) fuse, then go to step 26.
25. Replace the A/F sensor (Sensor 1) A/F Sensor Replacement.
26. Reconnect all connectors.
27. Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode.
28. Reset the PCM with the HDS.
29. Do the PCM idle learn procedure PCM Idle Learn Procedure.
30. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0135 and/or P0155* indicated?
YES -
Check for poor connections or loose terminals at the A/F sensor (Sensor 1), the PGM-FI subrelay, and the PCM, then go to step 1.
NO -
Go to step 31.
31. Monitor the OBD STATUS for DTC P0135 and/or P0155* in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
Troubleshooting is complete. If any other Pending or Confirmed DTCs were indicated in step 30, go to the indicated DTC's troubleshooting.
NO -
If the HDS indicates FAILED, check for poor connections or loose terminals at the A/F sensor(Sensor 1), the PGM-FI subrelay, and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, keep idling until a result comes on.
32. Reconnect all connectors.
33. Update the PCM if it does not have the latest software PCM Update, or substitute a known-good PCM.
34. Start the engine, and let it idle.
35. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0135 and/or P0155* indicated?
YES -
Check for poor connections or loose terminals at the A/F sensor (Sensor 1), the PGM-FI subrelay, and the PCM. If the PCM was updated, substitute a known-good PCM, then go to step 34. If the PCM was substituted, go to step 1.
NO -
Go to step 36.
36. Monitor the OBD STATUS for P0135 and/or P0155*in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM Service and Repair. If any other Pending or Confirmed DTCs were indicated in step 35, go to the indicated DTC's troubleshooting.
NO -
If the HDS indicates FAILED, check for poor connections or loose terminals at the A/F sensor(Sensor 1), the PGM-FI subrelay, and the PCM. If the PCM was updated, substitute a known-good PCM, then go to step 34. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, keep idling until a result comes on.