2/3 Backrest Section
1 - Locking lever
- Remove bolts -2- (2x) in lock trim -3-.
- Detach locking lever from underneath at hooks (2x).
- Using screwdriver, pry out locking lever at top.
2 - Screws
3 - Lock trim
4 - Outer head restraint
- Outer rear head restraints are not identical to front head restraints. Mark accordingly using adhesive tape if all head restraints are removed together
5 - Backrest panel
6 - Head restraint guides
- Always install guide with button on left-side
- Button should always face toward left
7 - Upholstery clips
8 - Backrest heating element
9 - Warning indicator
- With backrest locked in position, pin protrudes 1-2 mm (approx. 1/16 in.) above lock trim
- With backrest unlocked, pin protrudes approx. 20 mm (3/4 in.) above lock trim and red mark is visible
10 - Center head restraint
11 - Center armrest
12 - Ski sack
- If installing new seat cover, cut hole in fabric for ski sack. Service and Repair
13 - Center head restraint guides
- Both are equipped with buttons
- Buttons must always face toward left
14 - Fastening groove
15 - Rear fastening strip (all around)
16 - Fastening strip at head restraint
17 - Hook
18 - Retaining tabs
19 - Trim for three-point seat belt
- Removing and installing. See "Third Rear Three-Point Seat Belt/Folding Backrest".
20 - Lock cylinder
- Use ignition key when removing and installing lock cylinder
- Remove locking lever.
- Using screwdriver, pry out retaining tabs and press out lock cylinder -20-.
21 - Wire clips
Removing:
- Remove backrest. Service and Repair
- Remove screws -2- (2x) from lock trim -3-.
- Press catch on left head restraint guide -6- and remove head restraint -4-.
- Press buttons on left and right head restraint guides -13- and remove center head restraint -10-.
- Remove center armrest -11-.
- Remove ski sack -12-. Service and Repair
- Remove head restraint guides -13- (See Fig. 1) and -6- (See Fig. 2).
- Pry fastening strip -15- from backrest panel -5-.
- Using screwdriver, pry out trim for three-point seat belt -19-.
- Detach hooks -17- from wire clips -21-.
- Using screwdriver, pry fastening strip -16-from fastening groove -14-.
- Cut through upholstery clips -7- and remove seat cover.
- Remove backrest heating element -8-.
Installing:
- Use VAG1634 stapling tool to install new upholstery clips.
- When installing new backrest panel, bend retaining tabs -18- inward approx. 1-2 mm (1/16 in.) for better support for fastening strip.
NOTES: Check the following after completing the installation of the backrest:
- The seat belt guide component and the belt webbing must not make contact with or rub against the seat foam or the seat cover fabric.
- The guide component must follow all movements of the belt webbing.
- The belt webbing must run freely in all directions.
Fig. 1 Removing guides for center head restraint
- Using screwdriver -2-, pry out center head restraint guide -1-.
Fig. 2 Removing head restraint guides
NOTE: Head restraint guide -1- is shown removed in the illustration.
1 - Head restraint guide
2 - Retainer tab
3 - Screwdriver or upholstery needle Max. width 2 mm (25/32 in.)
4 - Hole
- Insert screwdriver or upholstery needle -3- (max. width 2 mm or 0.079 in.) into hole -4- (opposite retaining clip for head restraint guide).
- Pry screwdriver -3- in direction of arrow -A-, press retainer tab -2- in direction of arrow -B- and remove head restraint guide -1-.