Diagnostic Mode 06: Checking Test Results of Components That Are Not Continuously Monitored

Diagnostic mode 6: Checking test results of components that are not continuously monitored

Diagnostic Mode 06 displays the test results of emission related components and systems which are not continuously monitored.

The values of the individual test results must reach the specified value or must be within the min. and max. limits.

Note: Depending on the scan tool and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).

Test requirements

- Exhaust system must be properly sealed between catalytic converter and cylinder head.
- No DTCs in the DTC memory.
- Coolant temperature at least 80�C.

Work procedure

- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select the desired "Test-ID".

The current minimum and maximum values will be displayed on the scan tool screen.






Test-ID 01 ($01): Catalytic Conversion (Bank 1).

- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
- Select "Test-ID 01 ($01)".
- Select the desired "Test-ID".
- Check specified values at idle.






- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.

End of diagnosis.

Test-ID 01 ($01): Catalytic Conversion (Bank 2).

- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 01 ($01)".

- Select the desired "Test-ID".
- Check specified values at idle.






- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Diagnostic Mode 03: Interrogating Fault Memory
- Switch the ignition off.

End of diagnosis.

Test-ID 02 ($02): Oxygen Sensor (Bank 1, Sensor 1).

- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 02 ($02)".

- Select the desired "Test-ID".
- Check specified values at idle.






- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.

End of diagnosis.

Test-ID 02 ($02): Oxygen Sensor (Bank 2, Sensor 1).

- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 02 ($02)".

- Select the desired "Test-ID".
- Check specified values at idle.






- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.

End of diagnosis.

Test-ID 03 ($03): Secondary Air Injection (AIR) System (Bank 1).

- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 33 ($21)".

- Select the desired "Test-ID".
- Check specified values at idle.






- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.

End of diagnosis.

$05 (05): Tank Ventilation System, Tank Vent Valve Function Check

- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 05 ($05)".

- Select the desired "Test-ID".
- Check specified values at idle.






- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.

End of diagnosis.

Test-ID 05 (05): Tank Ventilation System, Tank Leak Test

- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 05 ($05)".

- Select the desired "Test-ID".
- Check specified values at idle.






- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure.
- Switch the ignition off.

End of diagnosis.