Overview of Removed Parts With Hydraulic Control -E18/2-
Overview of Removed Parts With Hydraulic Control -E18/2-
1. Drain plug - 40 Nm (30 ft lb)
5 mm hex socket
Remove to drain ATF
2. Seal
Always replace
3. Bolt - 10 Nm (7 ft lb)
Tighten bolts for oil pan diagonally in several stages
4. Oil pan
Removing and installing Oil Pan, Removing and Installing
5. Gasket
Always replace
6. ATF strainer
Removing and installing Oil Strainer, Removing and Installing
7. Bolt - 8 Nm (70 inch lb)
For mounting valve body: 1 bolt M6 x 30, 16 bolts M6 x 60
Observe tightening method
8. Valve body
Remove and installing Valve Body, Removing and Installing
Allocation according to transmission code letters, refer to the parts catalog
9. Bolt - 8 Nm (70 inch lb)
10. Bracket
For wiring harness
Hook in wiring harness
Mounted with valve body bolts
11. Bolt - 6 Nm (53 inch lb)
12. Transmission Vehicle Speed Sensor (VSS) -G38-
Removing and installing, refer to Transmission Speed Sensor, A/T - Service and Repair - Procedures Service and Repair
13. Spacer sleeve
Height: 8mm
14. Inner oil line
Always replace
Removing and installing, refer to Fluid Line/Hose, A/T - Service and Repair - Procedures Service and Repair
15. O-ring
Always replace
16. Speedometer Vehicle Speed Sensor (VSS) -G22-
Removing and installing, refer to Powertrain Management - Computers and Control Systems - Vehicle Speed Sensor - Service and Repair - Procedures Service and Repair
17. O-ring
Always replace
Coat with Vaseline
18. Multi-Function Transmission Range Switch (TR) -F125-
Removing and installing Transmission Position Switch/Sensor, A/T - Service and Repair - Procedures
Replacing shift rod sealing ring
19. Bolt - 8 Nm (70 inch lb)
20. O-ring
Always replace
21. Locking clamp
22. Wiring harness in transmission
Always replace
Transmission Fluid Temperature Sensor -G93- integrated in wiring harness
Remove and install valve body to install Valve Body, Removing and Installing
Unhook from bracket for wiring harness -item 10-
Installtion position wiring harness connector: flat part of rear collar points toward oil pan, the tabs at collar are horizontal
23. Bolt - 9 Nm (79.63 inch lb)
24. Sensor for transmission RPM -G182-
Removing and installing, refer to Transmission Speed Sensor, A/T - Service and Repair - Procedures Service and Repair
25. Connector
Is connected at wiring harness in transmission
Must be disconnected before removing the valve body
26. Bolt - 6 Nm (53 inch lb)
27. Bracket for solenoid valve
28. Solenoid Valve 4 -N91-
With O-ring
Remove and install valve body to install Valve Body, Removing and Installing
29. Solenoid Valve 3 -N90-
Without O-ring
Remove and install oil pan to replace Oil Pan, Removing and Installing
30. Solenoid Valve 2 -N89-
Without O-ring
Remove and install oil pan to replace Oil Pan, Removing and Installing
31. Bolt - 6 Nm (53 inch lb)
32. Bracket for solenoid valves
33. Solenoid Valve 6 -N93-
With O-ring
Remove and install oil pan to replace Oil Pan, Removing and Installing
34. Solenoid Valve 7 -N94-
With O-ring
Remove and install oil pan to replace Oil Pan, Removing and Installing
35. Solenoid Valve 5 -N92-
With O-ring
Remove and install oil pan to replace Oil Pan, Removing and Installing
36. Solenoid Valve 1 -N88-
Without O-ring
Remove and install oil pan to replace and unbolt guide plate for park lock mechanism.
When installing, do not tighten bolts for guide plate (23 Nm) when selector lever is in position "P"
37. Bolt - 6 Nm (53 inch lb)
38. Magnet
4 pieces in the oil pan recesses
39. O-ring
Always replace
40. ATF check plug - 80 Nm (59 ft lb)
17 mm hex socket