Operation CHARM: Car repair manuals for everyone.
Home >> Audi >> 2001 >> TT Quattro Coupe (8N3) L4-1.8L Turbo (ATC) >> Repair and Diagnosis >> Accessories and Optional Equipment >> Navigation System >> Testing and Inspection >> Programming and Relearning

Programming and Relearning



Navigation System Nav 4 (BNS 4.0) From Calendar Week (KW) 04/01 On Board Diagnostic (OBD)

Adaptation (Function 10)

Using the adaptation function, the following changes can be made and saved.

- Changing tire size
- Changes of impulse number per wheel rotation (GALA)
- Deactivating and activating production diagnostic
- Connection of included or external loudspeakers
- Changing country selection
- Dynamic route guidance adaptation

Control module for navigation must be adapted, whether dynamic route guidance must be adapted and via which unit the respective information must be sent: RDS radio with TMC and/or telephone.

The navigation system uses the speed signal from speedometer (GALA) for calculating mileage.

Individual functions are called up by entering the appropriate adaptation channel numbers (see adaptation table).

Adaptation table:







Initiating "Adaptation" function 10

Indicated on display:

Rapid data transfer HELP
Select function XX

- Press buttons -1- and -0-. This selects "Adaptation", function 10.

Indicated on display:

Rapid data transfer Q
10 -Adaptation

- Press -Q- button to confirm input.

Indicated on display:

Adaptation
Enter channel number XX

- Enter desired adaptation channel (adaptation table).
- Press -Q- button to confirm input.

NOTE: After changing an adaptation value or ending an adaptation channel, "Adaptation" function 10 must be performed again before selecting another adaptation channel.

Adapt tire circumference

Indicated on display.

Adaptation
Enter channel number XX

- Press buttons -0- and -1-. (01 selects "channel 1".)

NOTE: An erroneous entry can be corrected by pressing button -C-.

- Press -Q- button to confirm input.

Indicated on display:

Channel 1 adaptation 2060 ->
<-1 3->

The selected channel and the currently stored tire circumference (in mm) will be displayed in the top line.

- Press -> button.

Indicated on display:

Channel 1 adaptation 2060 ->
Enter adaptation value XXXXX

- Input new tire circumference, place a -0- before the 4 digit number (e.g. 01930).

See Tire table below.

- Press -Q- button to confirm input.

Indicated on display:

Channel 1 adaptation 1930 Q
<-1 3->

- Press -Q- button to confirm input.

Indicated on display:

Channel 1 adaptation 1930 Q
Store modified value?

- Press -Q- button to confirm input.

Indicated on display:

Channel 1 adaptation 1930 ->
Modified value has been stored

- Press -> button.

Indicated on display:

Rapid data transfer HELP
Select function XX

- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.

Adapt impulse number/wheel rotation (GALA)

Indicated on display:

Adaptation
Enter channel number XX

- Press buttons -0- and -2-. 02 selects "channel 2"

NOTE: An erroneous entry can be corrected by pressing button -C-.

- Press -Q- button to confirm input.

Indicated on display:

Channel 2 adaptation 4 ->
<-1 3->

The selected channel and the currently stored impulse number are displayed on the top line.

- Press -> button.

Indicated on display:

Channel 2 adaptation 4 ->
Enter adaptation value XXXXX

- Enter new impulse number, and place 4 times 0 in front of the number.

Impulse number 8 is always valid for Audi TT with navigation 4.

- Press -Q- button to confirm input.

Indicated on display:

Channel 2 adaptation 8 Q
<-1 3->

- Press -Q- button to confirm input.

Indicated on display:

Channel 2 adaptation 8 Q
Store modified value?

- Press -Q- button to confirm input.

Indicated on display:

Channel 2 adaptation 8 ->
Modified value has been stored

- Press -> button.

Indicated on display:

Rapid data transfer HELP
Select function XX

- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.

Adapting production diagnostic (function status register)

Indicated on display:

Adaptation
Enter channel number XX

- Press buttons -0- and -3-. (03 selects "channel 3".)

NOTE: An erroneous entry can be corrected by pressing button -C-.

- Press -Q- button to confirm input.

Indicated on display:

Channel 3 adaptation 0 ->
<-1 3->

The selected channel and the condition of the production diagnostic (function status register) is displayed in the upper line (0 = deactivated, 1 = active).

- Press -> button.

Indicated on display:

Channel 3 adaptation 0 ->
Enter adaptation value XXXXX

- Enter new adaptation value (e.g. 00001), where 00000 = product diagnostic deactivated and 00001 = product diagnostic active.
- Press -Q- button to confirm input.

Indicated on display:

Channel 3 adaptation 1 Q
<-1 3->

- Press -Q- button to confirm input.

Indicated on display:

Channel 3 adaptation 1 Q
Store modified value?

- Press -Q- button to confirm input.

Indicated on display:

Channel 3 adaptation 1 ->
Modified value has been stored

- Press -> button.

Indicated on display:

Rapid data transfer HELP
Select function XX

- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.

Adapting speaker connection

Indicated on display:

Adaptation
Enter channel number XX

- Press buttons -0- and -4-. (04 selects "channel 4",)

NOTE: An erroneous entry can be corrected by pressing button -C-.

- Press -Q- button to confirm input.

Indicated on display:

Channel 4 adaptation 0 ->
<-1 3->

The selected channel and the condition and the type of speaker connection is displayed in the upper line (0 = external radio, 1 = own speaker). If a radio system is installed, front left speakers are used, otherwise a separate speaker (hands-free speaker) is installed.

- Press -> button.

Indicated on display:

Channel 4 adaptation 0 ->
Enter adaptation value XXXXX

- Enter new adaptation value (e.g. 00001), where 00000 = external radio and 00001 = separate speaker.
- Press -Q- button to confirm input.

Indicated on display:

Channel 4 adaptation 1 Q
<-1 3->

- Press -Q- button to confirm input.

Indicated on display:

Channel 4 adaptation 1 Q
Store modified value?

- Press -Q- button to confirm input.

Indicated on display:

Channel 4 adaptation 1 ->
Modified value has been stored

- Press -> button.

Indicated on display:

Rapid data transfer HELP
Select function XX

- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.

Adapt country selection

Indicated on display:

Adaptation
Enter channel number XX

- Press buttons -0- and -5-. (05 selects "channel 5".)

NOTE: An erroneous entry can be corrected by pressing button -C-.

- Press -Q- button to confirm input.

Indicated on display:

Channel 5 adaptation 0 ->
<-1 3->

The selected channel and the country selection is displayed in the upper line (0 = Europe, 1 = USA).

- Press -> button.

Indicated on display:

Channel 5 adaptation 0 ->
Enter adaptation value XXXXX

- Enter new adaptation value (e.g. 00001), where 00000 = Europe and 00001 = USA.
- Press -Q- button to confirm input.

Indicated on display:

Channel 5 adaptation 1 Q
<-1 3->

- Press -Q- button to confirm input.

Indicated on display:

Channel 5 adaptation 1 Q
Store modified value?

- Press -Q- button to confirm input.

Indicated on display:

Channel 5 adaptation 1 ->
Modified value has been stored

- Press -> button.

Indicated on display:

Rapid data transfer HELP
Select function XX

- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.

Adapting dynamic route guidance
The control module is informed about whether dynamic route guidance should be adjusted and via which channels the respective information must be related.

Indicated on display:

Adaptation
Enter channel number XX

- Press buttons -0- and -6-. (06 selects "channel 6".)

NOTE: An erroneous entry can be corrected by pressing button -C-.

- Press -Q- button to confirm input.

Indicated on display:

Channel 6 adaptation 0 ->
<-1 3->

The selected channel and the respective system configuration are
displayed on the top line.

0 = without dynamic route guidance
1 = with dynamic route guidance and RDS radio with TMC
2 = with dynamic route guidance and RDS radio with TMC and telephone

- Press -> button.

Indicated on display:

Channel 6 adaptation 0 ->
Enter adaptation value XXXXX

- Enter new adaptation value (e.g. 00001), where 00001 = dynamic route guidance and RDS radio with TMC.
- Press -Q- button to confirm input.

Indicated on display:

Channel 6 adaptation 1 Q
<-1 3->

- Press -Q- button to confirm input.

Indicated on display:

Channel 6 adaptation 1 Q
Store modified value?

- Press -Q- button to confirm input.

Indicated on display:

Channel 6 adaptation 1 ->
Modified value has been stored

- Press -> button.

Indicated on display:

Rapid data transfer HELP
Select function XX

- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.

Tire table for Audi TT:

Tire size Circumference (mm)

205/55 R16 1930
225/45 R17 1930
225/40 ZR18 1943






pro multis · About Operation CHARM