Installation Position, Overview

Installation position, overview
1. Harness connector for engine bank 1 Oxygen Sensor (02S) behind Three Way Catalytic Converter (TWC) -G130- and heater for oxygen sensor 1 -Z29
^ 4 pin/green
2. Harness connector for engine bank 2 Oxygen Sensor (02S) 2 behind Three Way Catalytic Converter (TWC) -G131- and heater for oxygen sensor 2 -Z30 =>
^ 4 pin/brown
3. Harness connector for engine bank 1 Oxygen Sensor (02S) behind Three Way Catalytic Converter (TWC) -G39- and Oxygen Sensor (02S) heater -Z19
^ 4 pin/black
4. 3-way connector
^ For Knock Sensor (KS) 1- G61 -
5. Engine - Coolant Temperature (ECT) sensor -G62
^ At coolant line behind cylinder head engine bank 1
6. Wastegate bypass regulator valve -N75
7. Evaporative transmission (EVAP) canister purge regulator valve -N80
8. Sensor -1 for exhaust temperature -G235
^ At the left rear of the intake manifold; for vehicles with automatic transmission sensor -2- , exhaust temperature -G236- is also installed at this position.
9. Secondary Air Injection (AIR) solenoid valve -N112
^ Only for vehicles with automatic transmission
10. Secondary Air Injection (AIR) pump motor -V101
^ Only for vehicles with automatic transmission
11. Sensor -1- for exhaust temperature -G236
^ For vehicles with automatic transmission, this sensor is located at position -8- along with sensor -1 -for exhaust temperature -G235-. The two sensors are installed in series.
12. Recirculating -valve for turbocharger -N249
13. Fuel pressure regulator
14. Camshaft Position (CMP)sensor -G40
^ Engine bank 2
15. Secondary Air Injection (AIR) pump relay -J299
^ Only for vehicles with automatic transmission
16. Motronic Engine Control Module (ECM) - J220
17. 3-way connector
^ For Engine Speed (RPM) sensor -G28
^ Gray
18. 3-way connector
^ For Knock Sensor (KS) 2-G66
19. Harness connector for Heated Oxygen Sensor (HO2S) 2 -G108 and Oxygen Sensor (02S) 2 heater -Z28
^ 4 pin/black
20. Valve -2 -for camshaft adjustment -N208
21. Throttle Valve Control Module - ~1338
^ With throttle drive (power accelerator actuation) -G186-, angle sensor -1 for throttle drive (power accelerator actuation) -G187-, and angle sensor -2 for throttle drive (power accelerator actuation) -G188
22. Charge air pressure sensor -G31
^ Located in rubber shroud in front of throttle valve control module
23. Camshaft Position (CMP)sensor 2 -G163
^ Engine bank 1
24. Power output stage 2 -N192
^ For ignition coils engine bank 2
25. Power output stage -N122
^ For ignition coils engine bank 1
26. Valve -1 -for camshaft adjustment -N205
27. Engine bank 1, Heated Oxygen Sensor (HO2S) -G39- Z19
28. Knock Sensor (KS) 1-G61
29. Knock Sensor (KS) 2-G66
30. Engine Speed (RPM) sensor -G28
^ Located in transmission housing above sensor disk
31. Engine bank 2, Heated Oxygen Sensor (HO2S) 2 -G108- -Z28
32. Ignition coils engine bank 2
^ Ignition coil 4 -N163
^ Ignition coil 5N164
^ Ignition coil 6N189
33. Fuel injectors
Cylinder bank 2
^ Cylinder 4 fuel injector -N33
^ Cylinder 5 fuel injector -N83
^ Cylinder 6 fuel injector -N84
34. Intake Air Temperature (IAT) sensor -G42
^ On the lower front part of the intake manifold, near the throttle valve control module
35. 2-way connector
^ For Intake Air Temperature (IAT) sensor (measurements are made at this connector)
36. Fuel injectors
Cylinder bank 1
^ Cylinder 1 fuel injector -N30
^ Cylinder 2 fuel injector -N31
^ Cylinder 3 fuel injector -N32
37. Ignition coils engine bank 1
^ Ignition coil 1-N
^ Ignition coil 2-N128
^ Ignition coil 3-N158
38. Mass Air Flow (MAP)sensor -G70