Vehicle Diagnosis, Measuring and Information System VAS 5051 or V.A.G 1551 Scan Tool, Connecting and Selecting Functions
Vehicle Diagnosis, Measuring and Information System VAS 5051 or V.A.G 1551 scan tool, connecting and selecting functions - 5 Spd. Automatic Transmission 01V
Test requirements
^ Selector lever in "P" position and parking brake applied.
^ Vehicle voltage supply OK
^ Power supply and fuses for respective system OK
^ Ground (GND) connections and Ground point for transmission OK
- Check Ground connections for corrosion and damage and repair if necessary.
- Check battery Ground (GND) strap and Ground strap between battery and transmission.
- Switch ignition off.
For vehicles up to m. y. 2000
- The Data Link Connector (DLC) is located behind the cover in the rear ash tray (center console) for vehicles up to m. y. 2000
- Open rear ashtray (center console) and remove cover for DLC.
- Connect VAS 5051 tester to vehicle with VAS 5051/1 diagnostic cable. Alternately, V.A.G 1551 Scan Tool can also be used, using VAG 1551/3 adapter.
For vehicles from m. y. 2000
- The Data Link Connector (DLC) is located below the kneebar left of the steering wheel. for vehicles up to m. y. 2000
- Connect VAS 5051 tester to vehicle with VAS 5051/1 diagnostic cable. Alternately, V.A.G 1551 Scan Tool can also be used, using VAG 1551/3 adapter.
CAUTION:
^ When performing road tests with testers and measuring equipment, such equipment must only be operated from the rear seat.
^ Observe all safety precautions
Note:
The following description applies to the V.A.G 1551 Scan Tool. For the Vehicle Diagnosis, Measuring and Information System VAS 5051 please refer to the operating instructions.
VAG - On Board Diagnostic HELP
1 - Rapid data transfer
2 - Blink code output
Indicated on display 1)
1) Operating modes 1 and 2 are displayed alternately
Note:
^ Get additional operating instructions by pressing the HELP key of V.A.G 1551.
^ Use the -> key to advance within the program sequence.
^ An automatic check (keys 00) can be done in operating mode 1 "Rapid data transfer". This way all vehicle control modules will be checked automatically.
- Switch on ignition.
- Switch on printer with the Print key (indicator lamp in key lights up).
- Press key 1 for "Rapid data transfer" mode.
Rapid data transfer HELP
2 Enter address word XX
Indicated on display:
- Press keys 0 and 2. (Enter the address word "transmission electronics" with 02.)
Rapid data transfer Q
202 Transmission electronics
Indicated on display:
- Press Q button to confirm entry.
8D0927156BT AG5 01V 2.81V USA 1416 -
Coding 00002 WSC 00000
Appears on display:
The control module identification is displayed:
Control module identification
Depending on the software version, the control module may indicate a different control module identification as shown in this example.
^ 8DO927156BT- Part number
^ AG5 01V 5-speed automatic transmission 01V
^ 2.81 5V- Engine version
^ USA: (country), USA and CANADA
^ 1416: 14 = program version; 16 = data version
^ Coding 00002
^ WSC 00000: Dealer number of V.A.G 1551, with the last coding was performed
Control module does not answer! HELP
Indicated on display:
- By pressing the HELP key, a list of possible malfunction is printed out.
- After eliminating the possible causes of malfunctions, enter address word 02 for "transmission electronics" and confirm.
If again "Control module does not answer!" appears:
Control module does not answer! HELP
Indicated on display:
Check control module voltage supply.
- Perform test step 1.
- Check wiring connections to diagnostic connectors
- Replace control module if necessary
- Press -> key.
Rapid data transfer HELP
Select function XX
Indicated on display:
- After the HELP key is pressed, a list of possible functions is printed out.