Center Console (With Extension), Removing and Installing
Center Console (with Extension), Removing And Installing
Special tools, testers and auxiliary items required
- Disassembly tool 3409
- Protective cap VAS 6223/9
- Radio release tool T10057
Removing
NOTE All cable ties unfastened or cut open upon removal are to be re-attached at the same location on installation.
CAUTION: On vehicles equipped with Audi Telematics by OnStar, switch-off emergency (back-up) battery for Telematic/Telephone Control Module prior to disconnecting vehicle battery. Switch-on emergency (back-up) battery after reconnecting vehicle battery.
- Switch off ignition and remove ignition key.
- With ignition switched off, disconnect earth wire at battery.
CAUTION: When disconnecting battery observe necessary safety measures.
- Remove center console extension.
- Unscrew nuts at rear.
- Move front seats to rearmost position and set backrests to 45 degrees position.
- Remove airbag unit and steering wheel.
CAUTION: Observe safety precautions for working on airbags.
- Remove left instrument panel end trim - arrow -.
- Separate trim panel - 1 - from instrument panel using Trim removal wedge 3409 - arrows -.
- Open storage compartment.
- Slide trim for storage compartment to left out of fastener - arrow - and remove.
- Open glove box.
- Starting from above glove box, carefully separate trim panel - 1 - with switch module from instrument panel using Trim removal wedge 3409.
- Open glove box.
- Starting from above glove box, carefully separate trim panel - 1 - with switch module from dash panel using disassembly tool 3409.
NOTE Take particular care when unfastening clip on driver side end of trim panel.
- Disconnect connector.
- Remove knee bar - arrows -
- Disconnect connectors.
- Vehicles with knee airbag: Pull catch - 2 - in - direction of arrow - and disconnect connectors - 1 - and - 3 -.
- Remove right instrument panel end trim - arrow -.
- If applicable, remove CD changer as follows:
- Insert 2 keys of radio release tool T10057 in front of CD changer.
- Top L-top left
- Top R-top right
- Pull CD changer out of mounting frame.
- Disconnect connector.
- Disconnect connector for optical fibre.
- Open wiring harness connector protective cap - 2 - of wire with Protective cap VAS 6223/9-Item 1-.
NOTE Protective cap is designed to prevent contamination of or mechanical damage to end face of optical fibre, which would impair signal transmission.
- Press catches at CD changer and pull release tool out of CD changer.
- If applicable, remove storage compartment in glove box. To do so, use small screwdriver to release retainer tabs - 1 - and - 2 - in-direction of arrow-.
- Remove storage compartment out of glove box.
- Remove bolts - arrows -.
- Remove bolts - 1 - and - 2 -
- Disconnect connector - 1 - for glove box wiring harness - 2 - from supply lead - 3 -.
- Vehicles with knee airbag: Pull catch - 2 - in-direction of arrow-and disconnect connectors - 1 - and - 3 -.
- Remove glove box.
Vehicles with split center armrest
- Fold center armrests upward.
- Remove armrest hinge trim - arrow -.
- Remove bolts - arrows -.
- Disconnect connectors for storage compartment light (accessible through opening for rear ventilation).
- Remove center armrests.
Vehicles with one-piece center armrest
- Fold center armrest upward.
All models
- Use disassembly tool 3409 to remove front corners of storage compartment out of center console - arrow - 1 - and pull storage compartment forward - arrow 2 -.
- Disconnect connectors - 1 - and - 2 - and remove storage compartment.
- disconnect connectors - 1 -.
- Remove bolts - arrows - on either side of center console.
- Press button - arrow - and remove insert - 1 - for front ashtray.
- Remove bolt - arrow - and remove housing for front ashtray.
- Disconnect connector.
- Remove center console switch trim - arrows -
- Disconnect connectors.
- Remove bolts - 2 -.
- Release retaining springs - 1 - with small screwdriver - arrow -
- Swivel top edge of Climatronic Control Module J255 to rear.
- Remove Climatronic Control Module J255 out of mount.
- Disconnect connectors - A through E-by releasing retainer tab - G -.
- Disconnect connector - F -.
- Remove bolts - arrows -.
- Use screwdriver, for example, to press on rocker - A - of selector lever emergency release mechanism.
- At the same time, move selector lever from "P" to "D".
- Turn collar - 1 - to left and push it down as far as it will go.
- Lift off knob - 2 - for selector lever.
- Release fasteners - 1 - on either side of shift mechanism - arrow - and lift up trim panel - 3 -.
- Disconnect connector - 2 - and remove trim panel.
- Raise center console at rear and disconnect connectors on underside of center console.
- Remove center console to rear.
Installing
Install in reverse order, paying attention to the following:
- On installing trim panel - 1 - with switch module, make sure both catches are inserted in center of trim panel between instrument panel and monitor housing - arrows -.
CAUTION: When disconnecting battery observe necessary safety measures
Tightening torques
