Divided Backrest Cover and Upholstery, Removing and Installing
Divided Backrest Cover And Upholstery, Removing And Installing
1/3 backrest Cover And Upholstery, Removing And Installing
- Removal:
- Remove backrest.
- Remove bolt - 2 - of lock trim - 1 -.
- Press lock lever - 3 - in direction of arrow.
- Remove bolt - 4 - beneath lock lever - 3-.
- Lift latch trim - 1 - off.
- Remove headrests - 5 - :
- Headrests with slide in locking mechanism.
- Headrests without slide in locking mechanism.
- Remove headrest guides - 6 -.
- Headrest guides with slide in locking mechanism.
- Outer headrest guides without slide in locking mechanism.
- Inner headrest guides without slide in locking mechanism.
- Pry out rear plastic strip all around - 7 - and plastic strip - 8 - using a screwdriver and remove cushion from backrest panel.
- Turn back cover - 1 -.
- Pry out grip channels - 10 - from plastic clips - 11 - using a screwdriver.
1 - Latch trim
2 - Screw
3 - Lock lever
4 - Screw
5 - Headrest
- Outer rear headrests not the same as front headrests.
- If you remove all headrests, mark them with adhesive tape.
6 - Headrest guide (Qty. 2)
- With insertion lock: Removing and installing.
- Without insertion lock: Removing and installing.
7 - Rear plastic strip all around
8 - Plastic strip
9 - Cover
10 - Fastening strips (2x)
11 - Plastic clips
- Replace damaged plastic clips
2/3 backrest cover and upholstery, removing and installing
- Removal:
- Remove backrest.
- Remove bolt - 2 - (2x) of lock trim - 1 -.
- Press latch lever - 3 - in direction of arrow.
- Lift latch trim - 1 - off.
- Remove headrests - 4 - :
- Headrests with slide in locking mechanism.
- Headrests without slide in locking mechanism.
- Remove headrest guides - 5 -.
- Headrest guides with slide in locking mechanism.
- Outer headrest guides without slide in locking mechanism.
- Inner headrest guides without slide in locking mechanism.
- Remove center armrest - 11 -.
- Remove skisack - 11 -.
- Using a screwdriver, pry off cover for three-point seatbelt - 12 -.
- Pry off plastic strip - 6 - (4x) from brackets - 7 - (4x).
- Remove plastic strip - 8 - (4x) from bracket.
- Pry out rear plastic strip - 13 - all around using a screwdriver.
- Remove upholstery piece - 15 - from backrest panel - 9 -.
- Turn back cover - 14 -.
- Lever out grip channel - 16 - from plastic clip - 17 - using a screwdriver.
- Remove cover - 14 -.
1 - Latch trim
2 - Bolts (Qty. 2)
3 - Lock lever
4 - Headrest (Qty. 2)
- Outer rear headrests not the same as front headrests.
- If you remove all headrests, mark them with adhesive tape.
5 - Headrest guides (Qty. 4)
- Removing and installing.
- Install headrest guide with button at left.
6 - Plastic strip (Qty. 4)
7 - Bracket (Qty. 4)
8 - Plastic strip (Qty. 4)
9 - Backrest shell
10 - Center armrest
11 - Ski bag
12 - Three-point belt cover
13 - Rear plastic strip all around
14 - Cover
15 - Upholstery
16 - Fastening strip
17 - Plastic clips
- Replace damaged plastic clips
Check points after complete backrest installation
- Seat belt relay and belt webbing must not make contact with or rub against foam parts or seat cover fabric.
- Anti-twist stop must follow all movements of belt webbing.
- Belt webbing must move freely in all directions.
Lock cylinder, removing and installing
- Removal:
- Remove bolts - 2 - (2x) of lock trim - 3 -.
- Detach lock lever from below from catches (2x).
- Pry off top of lock lever using screwdriver.
- Installing:
Installation is reverse of removal.
1 - Lock lever
2 - Bolts
3 - Latch trim
4 - Latch trim
- When rear backrest is locked, pin - 1 - is 2 mm above lock trim.
- If rear backrest is not locked, pin lies approx. 20 mm above lock trim and a red mark is visible.
5 - Lock cylinder
- To remove and install the lock cylinder, ignition key must be inserted.