Diagnostic Mode 06: Checking Test Results of Components That Are Not Continuously Monitored
Diagnostic Mode 06: Checking Test Results Of Components That Are Not Continuously Monitored
Diagnostic Mode 06 displays the test results of emission related components and systems which are not continuously monitored.
The values of the individual test results must reach the specified value or must be within the min. and max. limits.
NOTE: Depending on diagnostic tester and protocol used, the information in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component- ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).
Test requirements
- Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.
- No DTCs stored in the DTC memory.
- Coolant temperature at least 80 degrees C.
Work procedure
- Connect the diagnostic tester.
- Start the engine and run at idle.
NOTE: If the engine does not start, crank the engine using starter for at least 5 seconds, do not switch the ignition off afterward under any circumstances.
- Select "Mode 6: Check test the results of components that are not continuously monitored" .
- Select the desired "Test-ID" of the component or system that is to be monitored, e.g. "Test-ID 01: Oxygen Sensor Monitor Bank 1 - Sensor 1" .
- Select the desired "Test-ID" .
The current minimum and maximum values will be displayed on the diagnostic tester screen.
The following table is a numerical list of all "Test-IDs" or "Hex-IDs" that may be selected.
Test-ID (Hex-ID) Component or System
01 ($01): Oxygen Sensor Monitor Bank 1 - Sensor 1
02 ($02): Oxygen Sensor Monitor Bank 1 - Sensor 2
33 ($21): Catalytic Converter Monitoring
59 ($3B): Fuel Tank EVAP System Integrity/Leak Test (0.40/1.0 mm)
60 ($3C): Fuel Tank EVAP System Integrity/Leak Test (0.20/0.5 mm)
61 ($3D): EVAP Valve Function Check
65 ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1
66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2
162 ($A2): Mis-Fire Cylinder 1 Data
163 ($A3): Mis-Fire Cylinder 2 Data
164 ($A4): Mis-Fire Cylinder 3 Data
165 ($A5): Mis-Fire Cylinder 4 Data
Test-ID 01 ($01): Oxygen Sensor Monitor Bank 1 - Sensor 1
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 01 ($01)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 02 ($02): Oxygen Sensor Monitor Bank 1- Sensor 2
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 02 ($02)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 33 ($21): Catalytic Converter Monitoring
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored" .
Select "Test-ID 33 ($21)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 59 ($3B): Fuel Tank EVAP System Integrity/Leak Test (0.40/1.0mm)
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored" .
Select "Test-ID 59 ($3B)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 60 ($3C): Fuel Tank EVAP System Integrity/Leak Test (0.20/0.5mm)
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 60 ($3C)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 61 ($3D): EVAP Valve Function Check
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored" .
Select "Test-ID 61 ($3D)" .
- Select the desired "Test-ID (TID)" or "Hex-ID" .
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 65 ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 65 ($41)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 66 ($42)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 162 ($A2): Mis-Fire Cylinder 1 Data
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 162 ($A2)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 163 ($A3): Mis-Fire Cylinder 2 Data
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6 Check test the results of components that are not continuously monitored" .
Select "Test-ID 163 ($A3):".
- Select the desired "Test-ID (TID)" or "Hex-ID" .
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 164 ($A4): Mis-Fire Cylinder 3 Data
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 164 ($A4)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 165 ($A5): Mis-Fire Cylinder 4 Data
- Connect the diagnostic tester.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored" .
Select "Test-ID 165 ($A5)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTCs or the corresponding diagnostic repair procedure. Mode 03: Interrogating Fault Memory
- Switch the ignition off.
- End of diagnosis.