Mode 6 Data
Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions
Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.
Depending on the scan tool and protocol used, the information displayed in Diagnostic Mode 06 may be referred to by different names such as Test-ID (CID), Hex-ID, Component-ID (CID), On-Board Diagnostic Monitor Identifier (OBDMID), or contain no name at all and may be referenced by only a number.
Test requirements
• Exhaust system must be properly sealed between catalytic converter and cylinder head.
• No DTCs in the DTC memory.
• Coolant temperature at least 80 °C.
Work procedure
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select the desired "Test-ID".
The current minimum and maximum values will be displayed on the scan tool screen.
Monitor ID $21(33): Catalytic Conversion (Bank 1)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $21(33) ".
- Select the desired "Component-ID (CID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $22 (34): Catalytic Conversion Bank 2
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $22 (34) ".
- Select the desired "Component-ID (CID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $01 (01): Oxygen Sensor In Front of Catalytic Converter (Bank 1- Sensor 1)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $01 (01): ".
- Select the desired "Component-ID (CID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $05 (05): Oxygen Sensor In Front of Catalytic Converter (Bank 2, Sensor 1)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $05 (05)".
- Select the desired "Component-ID (CID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID 02 ($02): Oxygen Sensor behind Catalytic Converter (Bank 1, Sensor 2)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID 02 ($02)".
- Select the desired "Component-ID (CID)" or "Hex-ID".
- Check specified values at idle.
- If any of the components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $06 (06): Oxygen Sensor behind Catalytic Converter (Bank 2, Sensor 2)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $06 (06)".
- Select the desired "Component-ID (CID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $71 (113): Secondary Air Injection System (Bank 1)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $71 (113) ".
- Select the desired "Component-ID (CID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $72 (114): Secondary Air Injection System (Bank 2)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $72 (114) ".
- Select the desired "Component-ID (CID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $3D (61): Tank Ventilation System, Tank Vent Valve Function Check
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $3D (61)".
- Select the desired "Component-ID (CID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $3A (58): Fuel Tank EVAP System Leak Test (0.090")
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $3A (58)".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $3B (59): Fuel Tank EVAP System Leak Test (0.040)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $3B (59)".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $3C (60): Fuel Tank EVAP System Leak Test (0.020"/ 0.5
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $3C (60) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $A2 (162): Combustion Misfire Cylinder 1 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $A2 (162) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
- End of diagnosis.
Monitor ID $A3 (163): Combustion Misfire Cylinder 2 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $A3 (163) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $A4 (164): Combustion Misfire Cylinder 3 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $A4 (164) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $A5 (165): Combustion Misfire Cylinder 4 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $A5 (165) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $A6 (166): Combustion Misfire Cylinder 5 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $A6 (166) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $A7 (167): Combustion Misfire Cylinder 6 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $A7 (167) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $A8 (168): Combustion Misfire Cylinder 7 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $A8 (168)".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $A9 (169):Combustion Misfire Cylinder 8 Data
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $A9 (169)".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $41 (65): Oxygen Sensor Heating in front of Catalytic Converter (Bank 1 - Sensor 1)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $41 (65) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $45 (69): Oxygen Sensor Heating in front of Catalytic Converter (Bank 2 - Sensor 1)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $45 (69) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $42 (66 ): Oxygen Sensor Monitoring Behind Catalytic Converter (Bank 1 - Sensor 2
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $42 (66 ) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.
Monitor ID $46 (70): Oxygen Sensor Monitoring Behind Catalytic Converter (Bank 2 - Sensor 2)
- Connect the scan tool.
- Start the engine and run at idle.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Monitor ID $46 (70) ".
- Select the desired "Component-ID (TID)" or "Hex-ID".
- Check specified values at idle.
- If any of components or systems fail to meet the specified values, refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
- Switch the ignition off.