Programming and Relearning
Adaptation (Function 10)
Using the adaptation function, the following changes can be made and saved.
- Changing tire size
- Changes of impulse number per wheel rotation (GALA)
- Deactivating and activating production diagnostic
- Connection of included or external loudspeakers
- Changing country selection
- Dynamic route guidance adaptation
Control module for navigation must be adapted, whether dynamic route guidance must be adapted and via which unit the respective information must be sent: RDS radio with TMC and/or telephone.
The navigation system uses the speed signal from speedometer (GALA) for calculating mileage.
Individual functions are called up by entering the appropriate adaptation channel numbers (see adaptation table).
Adaptation table:
Initiating "Adaptation" function 10
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press buttons -1- and -0-. This selects "Adaptation", function 10.
Indicated on display:
Rapid data transfer Q
10 - Adaptation
- Press -Q- button to confirm input.
Indicated on display:
Adaptation
Enter channel number XX
- Enter desired adaptation channel (adaptation table.
- Press -Q- button to confirm input.
NOTE: After changing an adaptation value or ending an adaptation channel, "Adaptation" function 10 must be performed again before selecting another adaptation channel.
Adapt tire circumference
Indicated on display:
Adaptation
Enter channel number XX
- Press buttons -0- and -1-. (01 selects "channel 1".)
NOTE: An erroneous entry can be corrected by pressing button -C-.
- Press -Q- button to confirm input.
Indicated on display:
Channel 1 adaptation 2060
<-1 3->
The selected channel and the currently stored tire circumference (in mm) will be displayed in the top line.
- Press -> button.
Indicated on display:
Channel 1 adaptation 2060 ->
Enter adaptation value XXXXX
- Input new tire circumference, place a -0- before the 4 digit number (e.g. 01930).
Tire table.
- Press -Q- button to confirm input.
Indicated on display:
Channel 1 adaptation 1930 Q
<-1 3->
- Press -Q- button to confirm input.
Indicated on display:
Channel 1 adaptation 1930 Q
Store modified value?
- Press -Q- button to confirm input.
Indicated on display:
Channel 1 adaptation 1930 ->
Modified value has been stored
- Press -> button.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.
Adapt impulse number/wheel rotation (GALA)
Indicated on display:
Adaptation
Enter channel number XX
- Press buttons -0- and -2-. 02 selects "channel 2"
NOTE: An erroneous entry can be corrected by pressing button -C-.
- Press -Q- button to confirm input.
Indicated on display:
Channel 2 adaptation 4 ->
<-1 3->
The selected channel and the currently stored impulse number are displayed on the top line.
- Press -> button.
Indicated on display:
Channel 2 adaptation 4 ->
Enter adaptation value XXXXX
- Enter new impulse number, and place 4 times 0 in front of the number.
Impulse number 8 is always valid for Audi TT with navigation 4.
- Press -Q- button to confirm input.
Indicated on display:
Channel 2 adaptation 8 Q
<-1 3->
- Press -Q- button to confirm input.
Indicated on display:
Channel 2 adaptation 8 Q
Store modified value?
- Press -Q- button to confirm input.
Indicated on display:
Channel 2 adaptation 8 ->
Modified value has been stored
- Press -> button.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.
Adapting production diagnostic (function status register)
Indicated on display:
Adaptation
Enter channel number XX
- Press buttons -0- and -3-. (03 selects "channel 3".)
NOTE: An erroneous entry can be corrected by pressing button -C-.
- Press -Q- button to confirm input.
Indicated on display:
Channel 3 adaptation 0 ->
<-1 3->
The selected channel and the condition of the production diagnostic (function status register) is displayed in the upper line (0 = deactivated, 1 = active).
- Press -> button.
Indicated on display:
Channel 3 adaptation 0 ->
Enter adaptation value XXXXX
- Enter new adaptation value (e.g. 00001), where 00000 = product diagnostic deactivated and 00001 = product diagnostic active.
- Press -Q- button to confirm input.
Indicated on display:
Channel 3 adaptation 1 Q
<-1 3->
- Press -Q- button to confirm input.
Indicated on display:
Channel 3 adaptation 1 Q
Store modified value?
- Press -Q- button to confirm input.
Indicated on display:
Channel 3 adaptation 1 ->
Modified value has been stored
- Press -> button.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.
Adapting speaker connection
Indicated on display:
Adaptation
Enter channel number XX
- Press buttons -0- and -4-. (04 selects "channel 4",)
NOTE: An erroneous entry can be corrected by pressing button -C-.
- Press -Q- button to confirm input.
Indicated on display:
Channel 4 adaptation 0 ->
<-1 3->
The selected channel and the condition and the type of speaker connection is displayed in the upper line (0 = external radio, 1 = own speaker). If a radio system is installed, front left speakers are used, otherwise a separate speaker (hands-free speaker) is installed.
- Press -> button.
Indicated on display:
Channel 4 adaptation 0 ->
Enter adaptation value XXXXX
- Enter new adaptation value (e.g. 00001), where 00000 = external radio and 00001 = separate speaker.
- Press -Q- button to confirm input.
Indicated on display:
Channel 4 adaptation 1 Q
<-1 3->
- Press -Q- button to confirm input.
Indicated on display:
Channel 4 adaptation 1 Q
Store modified value?
- Press -Q- button to confirm input.
Indicated on display:
Channel 4 adaptation 1 ->
Modified value has been stored
- Press -> button.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.
Adapt country selection
Indicated on display:
Adaptation
Enter channel number XX
- Press buttons -0- and -5-. (05 selects "channel 5".)
NOTE: An erroneous entry can be corrected by pressing button -C-.
- Press -Q- button to confirm input.
Indicated on display:
Channel 5 adaptation 0 ->
<-1 3->
The selected channel and the country selection is displayed in the upper line (0 = Europe, 1 = USA).
- Press -> button.
Indicated on display:
Channel 5 adaptation 0 ->
Enter adaptation value XXXXX
- Enter new adaptation value (e.g. 00001), where 00000 = Europe and 00001 = USA.
- Press -Q- button to confirm input.
Indicated on display:
Channel 5 adaptation 1 Q
<-1 3->
- Press -Q- button to confirm input.
Indicated on display:
Channel 5 adaptation 1 Q
Store modified value?
- Press -Q- button to confirm input.
Indicated on display:
Channel 5 adaptation 1->
Modified value has been stored
- Press -> button.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.
Adapting dynamic route guidance
The control module is informed about whether dynamic route guidance should be adjusted and via which channels the respective information must be related.
Indicated on display:
Adaptation
Enter channel number XX
- Press buttons -0- and -6-. (06 selects "channel 6".)
NOTE: An erroneous entry can be corrected by pressing button -C-.
- Press -Q- button to confirm input.
Indicated on display:
Channel 6 adaptation 0 ->
<-1 3->
The selected channel and the respective system configuration are displayed on the top line.
0 = without dynamic route guidance
1 = with dynamic route guidance and RDS radio with TMC
2 = with dynamic route guidance and RDS radio with TMC and telephone
- Press -> button.
Indicated on display:
Channel 6 adaptation 0 ->
Enter adaptation value XXXXX
- Enter new adaptation value (e.g. 00001), where 00001 = dynamic route guidance and RDS radio with TMC.
- Press -Q- button to confirm input.
Indicated on display:
Channel 6 adaptation 1 Q
<-1 3->
- Press -Q- button to confirm input.
Indicated on display:
Channel 6 adaptation 1 Q
Store modified value?
- Press -Q- button to confirm input.
Indicated on display:
Channel 6 adaptation 1 ->
Modified value has been stored
- Press -> button.
Indicated on display:
Rapid data transfer HELP
Select function XX
- Press buttons -0- and -6-. This selects "End Output", function 06.
- Press -> button.
Tire table for Audi TT:
Tire size Circumference (mm)
205/55 R16 1930
225/45 R17 1930
225/40 ZR18 1943