Controls, Housing

Electrical/electronic components and installed locations - 01V, 5 Speed A/T





1 - Transmission Control Module -J217-

2 - Data Link Connector (DLC)

3 - Multi-Function Transmission Range (TR) Switch -F125-

4 - Internal transmission wiring harness with integrated Transmission Fluid Temperature Sensor -G93- (ATF)

5 - Valve body

6 - Sensor for transmission RPM -G182-

7 - Transmission Vehicle Speed Sensor (VSS) -G38- (also designated as Sender for transmission output RPM -G195-)

8 - Tiptronic Switch -F189-

9 - Shift Lock Solenoid -N110-

10 - Throttle Position (TP) Sensor -G79- and -G185-

11 - Starting Interlock Relay -J207-

12 - Transmission Range (TR) Selector Lever Display -Y6-

13 - Brake light switch -F-





Fig. 1 Component location of Transmission Control Module (TCM) -J217-

Control module is located in left plenum chamber in e-box under Engine Control Module (ECM).

Removing and installing the control module

If control module for engine or transmission is replaced, the system must be put into basic setting.

- Perform basic setting in "Vehicle Self-Diagnosis" using the VAS 5051 tester.





Fig. 2 Disconnecting Transmission Control Module (TCM) -J217- from multi-pin harness connector

- Disengage harness connector (arrow) and disconnect it from Transmission Control Module (TCM).

Installation is the reverse of removal.





Fig. 3 Data Link Connector (DLC)

Installation location: Data Link Connector (DLC) is located under driver-side storage compartment.

- Connect VAS5051 tester to Data Link Connector (DLC) using VAS5051/1 diagnostic cable and adapter VAS 6017 with ignition switched off.





Fig. 4 Valve body

Installation location: Valve body is bolted on to transmission housing below and covered by transmission oil pan.

Solenoid valves -N88-, -N89-, -N90-, and pressure control valves -N215-, -N216-, -N217-, -N218- are fastened to valve body.





Fig. 5 Internal transmission wiring harness with integrated Transmission Fluid Temperature Sensor -G93- (ATF)

Installation location: Transmission Fluid Temperature Sensor (arrow) is located in the wiring harness on valve body.

Wiring harness may be replaced with transmission installed and valve body removed.





Fig. 6 Transmission Vehicle Speed Sensor (VSS) -G38-

Installation location: Transmission Vehicle Speed Sensor is located on rear right of transmission. Also referred to as the sender for transmission output RPM -G195-.





Fig. 7 Sensor for transmission RPM -G182-

Sensor for transmission RPM -A- is fastened to transmission housing behind valve body. This sensor is a Hall sensor.





Fig. 8 Multi-Function Transmission Range (TR) Switch -F125-

Installation location: Multi-Function Transmission Range (TR) Switch -1- is located at left on transmission; multi-pin connector for Multi-Function Transmission Range (TR) Switch -2-.





Fig. 9 Tiptronic Switch -F189-

Installation location: Tiptronic switch is integrated into circuit board of symbol insert, which is located in shift mechanism cover.





Fig. 10 Shift lock solenoid -N110-

Installation location: Shift lock solenoid is located in the shift mechanism -arrow-.





Fig. 11 Starting Interlock Relay -J207-

Installation location: Relay is located in central electronics.





Fig. 12 Throttle Position (TP) sensor -G79- and -G185-

Throttle Position (TP) sensor -G79- and -G185- (arrow), component of electronic engine power control (E-Gas), is located at pedal assembly.

The kick down function is performed (controlled) via Throttle Position (TP) sensor -G79- and -G185-.





Fig. 13 Brake light switch -F-

Installation location: Brake light switch (arrow) is located in foot pedal assembly.





Fig. 14 Transmission Range (TR) Selector Lever Display -Y6-

Installation location: in instrument cluster