Mode 6 Data

Diagnostic Modes

The information provided in Modes 01 through 09 displays the various levels of emission related data that may be monitored, as well as the ability to retrieve and read stored DTC trouble codes , erase stored DTC trouble codes, generate readiness codes, and select the various PIDs and Test-IDs used within the modes to monitor the engine, and emission related component parameters.

The following table provides a link to all diagnostic modes that monitor all components and systems which influence the emission quality.

• Depending on scan tool and protocol used, the information displayed may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), On-Board Diagnostic Monitor Identifier (OBDMID), or contain no name at all and be referenced by only a number.

Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions

Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.

The values of the individual test results must reach the specified value or must be within the min. and max. limits.

• Depending on diagnostic tester and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).

Test requirements

• Exhaust system must be properly sealed between catalytic converter and cylinder head.

• No DTCs in the DTC memory.

• Coolant temperature at least 80° C.

Work procedure

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select the desired "Test-ID".

The current minimum and maximum values will be displayed on the diagnostic tester screen.





Test-ID 01 ($01): Oxygen Sensor Monitor Bank 1 - Sensor 1.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 01 ($01)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 02 ($02): Oxygen Sensor Monitor Bank 1- Sensor 2.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 02 ($02)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 05 ($05): Oxygen Sensor Monitor Bank 2 - Sensor 1.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 05 ($05)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 06 ($06): Oxygen Sensor Monitor Bank 2 - Sensor 2.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 06 ($06)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 33 ($21): Catalyst Monitor Bank 1.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 33 ($21)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 34 ($22): Catalyst Monitor Bank 2.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 34 ($22)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

$3A (58): Fuel Tank EVAP System Leak Test (0.090").

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 59 ($3B)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 59 (3B): EVAP Monitor (0.040).

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 59 ($3B)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 60 (3C): EVAP Monitor (0.020).

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 60 ($3C)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 61 (3D): Purge Flow Monitor.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 61 ($3D)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 65 ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 65 ($41)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 69 ($45): Oxygen Sensor Heater Monitor Bank 2 - Sensor 1.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 69 ($45)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 66 ($42)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 70 ($46): Oxygen Sensor Heater Monitor Bank 2 - Sensor 2.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 70 ($46)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 162 ($A2): Mis-Fire Cylinder 1 Data.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 162 ($A2)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 163 ($A4): Mis-Fire Cylinder 2 Data.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 163 ($A4)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 164 ($A4): Mis-Fire Cylinder 3 Data.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 164 ($A4)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 165 ($A5): Mis-Fire Cylinder 4 Data.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 165 ($A5)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 166 ($A4): Mis-Fire Cylinder 5 Data.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 166 ($A4)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 167 ($A7): Mis-Fire Cylinder 6 Data.

- Connect the diagnostic tester.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 167 ($A7)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.