Mode 6 Data
Diagnostic Modes 01 - 09
Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions
The information provided in Modes 01 through 09 displays the various levels of emission related data that may be monitored, as well as the ability to retrieve and read stored DTC trouble codes , erase stored DTC trouble codes, generate readiness codes, and select the various PIDs and Test-IDs used within the modes to monitor the engine, and emission related component parameters.
The following table provides a link to all diagnostic modes that monitor all components and systems which influence the emission quality.
• Depending on scan tool and protocol used, the information in diagnostic mode 01 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).
Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.
The min & max values for each individual test in Mode 05 represent the min & max operating values for a properly operating system. This data is provided to the individual aftermarket scan tool companies for development of their scan tool. Depending on the scan tool being used, the min & max values shown may vary, or be rounded up or down to the nearest decimal point depending on the aftermarket scan tool company's development process. e.g.:
Depending on the scan tool and protocol used, the information displayed in Diagnostic Mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), On-Board Diagnostic Monitor Identifier (OBDMID), or contain no name at all and may be referenced by only a number.
Test requirements
• Exhaust system must be properly sealed between the catalytic converter and the cylinder heads.
• No DTCs stored in the DTC memory.
• Coolant temperature at least 80° C.
Work procedure
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select the desired "Test-ID".
The current minimum and maximum values will be displayed on the scan tool screen.
OBDMID 01 ($01): Oxygen Sensor Monitor Bank 1 - Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 01 ($01)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0133:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 02 ($02): Oxygen Sensor Monitor Bank 1- Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 02 ($02)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0139:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 05 ($05): Oxygen Sensor Monitor Bank 2 - Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 05 ($05)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0153:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 06 ($06): Oxygen Sensor Monitor Bank 2 - Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 06 ($06)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0159:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 09 ($09): Oxygen Sensor Monitor Bank 3 - Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 09 ($09)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0133:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 10 ($0A): Oxygen Sensor Monitor Bank 3- Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 10 ($0A)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0139:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 13 ($0D): Oxygen Sensor Monitor Bank 4 - Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 13 ($0D)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0153:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 14 ($0E): Oxygen Sensor Monitor Bank 4 - Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 14 ($0E)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0159:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 33 ($21): Catalyst Monitor Bank 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 33 ($21)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0421:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 34 ($22): Catalyst Monitor Bank 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 34 ($22)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0431:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 36 ($24): Catalyst Monitor Bank 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 36 ($24)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0421:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 59 (3B): EVAP Monitor (0.040)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 59 ($3B)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0442-P2404:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 60 (3C): EVAP Monitor (0.020)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 60 ($3C)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0456:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 61 (3D): Tank Vent Valve function check
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 61 ($3D)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0441:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 65 ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 65 ($41)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0135:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 66 ($42)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0141:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 69 ($45): Oxygen Sensor Heater Monitor Bank 2- Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 69 ($45)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0155:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 70 ($46): Oxygen Sensor Heater Monitor Bank 2 - Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 70 ($46)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0161:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID $71 (113): Secondary Air Injection (AIR) System 1 (Bank 1)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 71 ($113)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0491:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID $72 (114): Secondary Air Injection (AIR) System 2 (Bank 2)
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 72 ($114)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0492:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 73 ($49): Oxygen Sensor Heater Monitor Bank 3 - Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 65 ($41)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0135:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 74 ($4A): Oxygen Sensor Heater Monitor Bank 3 - Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 74 ($4A)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0141:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 77 ($4D): Oxygen Sensor Heater Monitor Bank 4- Sensor 1
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 77 ($4D)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0155:
- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 78 ($4E): Oxygen Sensor Heater Monitor Bank 4 - Sensor 2
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 78 ($4E)".
- Select the desired "Test-ID".
- Check specified values at idle.
P0161:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 162 ($A2): Mis-Fire Cylinder 1 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 162 ($A2)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
P0301:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 163 ($A3): Mis-Fire Cylinder 2 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 163 ($A3)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
P0302:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 164 ($A4): Mis-Fire Cylinder 3 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 164 ($A4)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
P0303:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 165 ($A5): Mis-Fire Cylinder 4 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 165 ($A5)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
P0304:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 166 ($A6): Mis-Fire Cylinder 5 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 166 ($A6)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
P0305:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 167 ($A7): Mis-Fire Cylinder 6 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 167 ($A7)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
P0306:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
OBDMID 168 ($A8): Mis-Fire Cylinder 7 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "OBDMID 168 ($A8)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
P0307:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.
Test-ID 169 ($A9): Mis-Fire Cylinder 8 Data
- Connect the scan tool.
- Start the engine and let run at idle speed.
- Select "Mode 6: Check test the results of components that are not continuously monitored".
Select "Test-ID 169 ($A9)".
- Select the desired "Test-ID (TID)" or "Hex-ID".
- Check specified values at idle.
P0308:
- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory
- Switch the ignition off.
- End of diagnosis.