Seat Height Adjustment Motor (V245)/(V246)
Seat Height Adjustment Motor (V245)/(V246)
Special tools, testers and auxiliary items required
• Engine and Gearbox Support (VAS6095)
• Seat Repair Stand (VAS6136)
• Connector Test Set (V.A.G 1594C)
Removing
Follow all safety precautions when working on pyrotechnic components. Refer to => [ Restraint System Components General Safety Precautions ] .
- Remove the front seat. Refer to => [ Front Seat ] Front Seat.
- Disconnect the electrical connector on the seat forward/back adjustment motor.
- Remove the screw - 1 -; to do this, connect the contacts on the motor with a battery using the cables from the (V.A.G 1594C) and bring the seat adjustment into position.
- Remove the mount - 2 - for the belt latch - 3 - and disconnect the seat belt fastening sensor connector.
- Mount the (VAS 6136) on the (VAS 6095).
- Attach the seat to the (VAS 6136).
- Remove trim. Refer to => [ Trim ] Trim.
- Remove tunnel side trim panel. Refer to => [ Trim, Tunnel Side ] Trim, Tunnel Side.
- Create photos or sketches of wire securing and routing.
- Remove the front backrest. Refer to => [ Front Backrest ] Front Backrest.
• If the front backrest is not removed, the load on the seat frame will cause the ceramic sleeves to break.
- Remove the bolt - 1 -.
- Remove the nut - 4 - and then remove the screw - 3 -.
- Fold the seat pan - 2 - up - arrow - and secure it with a wooden block so it does not fold back down.
• Bushings - 1 - in the bearing locations on lower seat pan frame - 2 - must not be damaged when folding the frame upward.
- Disconnect electrical harness connector - 2 -.
- Remove the screws - arrows - and remove the height adjustment motor - 1 -.
Installing
Follow all safety precautions when working on pyrotechnic components. Refer to => [ Restraint System Components General Safety Precautions ] .
Installation is reverse of removal, noting the following:
• Damaged bushings - 1 - cannot be replaced with workshop materials.
• If the bushings are damaged, lower seat pan frame - 2 - must be replaced.
- Clean the threaded bolt holes for self-locking nuts, for example using a thread tap.
- Replace all self-locking bolts.
Before handling airbag units (for example, when disconnecting the harness connector), the person handling them must discharge static electricity. For example, by briefly touching the door striker pin.
- Make sure the clip - A - and plastic toothed segment collar - 2 - as well as locking pins - B arrows - are inserted correctly in holes on fitting - 1 -.
- Make sure the plastic toothed segment - 2 - is clipped to fitting - 1 - correctly.
Plastic toothed segment collar - arrow C - must contact fitting - 1 - evenly.
- Route and secure wiring according to photos or sketches that were made.
- Ensure all connectors are engaged correctly.
• Make sure the connectors are installed all the way in and are secure.
• Make sure the wires do not get caught.
Ignition must be on when connecting battery. If pyrotechnic components (for example, airbag, belt tensioner) are not repaired correctly, they may deploy unintentionally after connecting battery. Maintain personal safety when connecting the battery by staying out of airbag deployment areas, keeping a distance from belt tensioners/seat belts and ensuring no other people are in the vehicle interior at the moment when the battery is connected.
- Switch on ignition.
- Connect the battery ground cable with the ignition turned on.
- If the airbag indicator lamp (K75) indicates a fault after installation, the DTC memory must be checked, deleted and checked again using the Vehicle diagnostic tester.
- In the case of memory seats: perform a basic setting for the backrest or seat after installation of the seat in the vehicle using the Vehicle diagnostic tester.
Tightening specifications, refer to => [ Seat Height Adjustment Motor Overview ] Seat Height Adjustment Motor Overview.