Part 2

Diagnostic Modes - (Continued)

Test-ID 65 ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 65 ($41)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 69 ($45): Oxygen Sensor Heater Monitor Bank 2- Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 69 ($45)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 73 ($49): Oxygen Sensor Heater Monitor Bank 3 - Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 73 ($49)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 77 ($4D): Oxygen Sensor Heater Monitor Bank 4 - Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 77 ($4D)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 66 ($42)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 70 ($46): Oxygen Sensor Heater Monitor Bank 2 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 70 ($46)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 74 ($4A): Oxygen Sensor Heater Monitor Bank 3 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 74 ($4A)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 78 ($4E): Oxygen Sensor Heater Monitor Bank 4 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 78 ($4E)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID $71 (113): Secondary Air Injection (AIR) System 1 (Bank 1)

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 71 ($113)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID $72 (114): Secondary Air Injection (AIR) System 2 (Bank 2)

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 72 ($114)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID $73 (115): Secondary Air Injection (AIR) System 3 (Bank 3)

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 71 ($113)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID $74 (116): Secondary Air Injection (AIR) System 4 (Bank 4)

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 74 ($116)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 162 ($A2): Mis-Fire Cylinder 1 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 162 ($A2)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 163 ($A3): Mis-Fire Cylinder 2 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 163 ($A3)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 164 ($A4): Mis-Fire Cylinder 3 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 164 ($A4)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 165 ($A5): Mis-Fire Cylinder 4 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 165 ($A5)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 166 ($A6): Mis-Fire Cylinder 5 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 166 ($A6)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 167 ($A7): Mis-Fire Cylinder 6 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 167 ($A7)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 168 ($A8): Mis-Fire Cylinder 7 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 168 ($A8)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 169 ($A9): Mis-Fire Cylinder 8 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 169 ($A9)".

- Select the desired "Test-ID (TID)" or "Hex-ID ".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.