Part 1

Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions

Diagnostic Mode 06 makes it possible to retrieve test results for special components and systems which are continuously or not continuously monitored. If the diagnosis of a system is complete, the diagnostic result and the corresponding thresholds are saved and displayed in mode 06. This data remains saved (even with the ignition off) until either new diagnostic results become available or the DTC memory is erased.

The values of the individual test results must reach the specified value or must be within the min. and max. limits.

• Depending on the scan tool and protocol used, the information displayed in diagnostic mode 06 may be referred to by different names such as Test-ID (TID), Hex-ID, Component-ID (CID), or On-Board Diagnostic Monitor Identifier (OBDMID).

Test requirements

• Exhaust system must be properly sealed between catalytic converter and cylinder head.

• No DTCs in the DTC memory.

• Coolant temperature at least 80° C.

Work procedure

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select the desired "Test-ID".

The current minimum and maximum values will be displayed on the scan tool screen.









OBDMID 01 ($01): Oxygen Sensor Monitor Bank 1 - Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 01 ($01)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 02 ($02): Oxygen Sensor Monitor Bank 1- Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 02 ($02)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 05 ($05): Oxygen Sensor Monitor Bank 2 - Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 05 ($05)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 06 ($06): Oxygen Sensor Monitor Bank 2 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 06 ($06)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 09 ($09): Oxygen Sensor Monitor Bank 3 - Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 09 ($09)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 10 ($0A): Oxygen Sensor Monitor Bank 3 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 06 ($06)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 13 ($0D): Oxygen Sensor Monitor Bank 4 - Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 13 ($0D)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 14 ($0E): Oxygen Sensor Monitor Bank 4 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 14 ($0E)".

- Select the desired "Test-ID".

- Check specified values at idle.





OBDMID 33 ($21): Catalyst Monitor Bank 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 33 ($21)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 34 ($22): Catalyst Monitor Bank 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 34 ($22)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 35 ($23): Catalyst Monitor Bank 3

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 35 ($23)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

Test-ID 36 ($24): Catalyst Monitor Bank 4

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 35 ($23)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 58 ($3A): Fuel Tank EVAP System Leak Test (0.090")

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 59 ($3B)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 59 (3B): EVAP Monitor (0.040)

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 59 ($3B)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 60 (3C): EVAP Monitor (0.020)

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 60 ($3C)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 61 (3D): Tank Vent Valve function check

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 61 ($3D)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 65 ($41): Oxygen Sensor Heater Monitor Bank 1 - Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 65 ($41)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 66 ($42): Oxygen Sensor Heater Monitor Bank 1 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 66 ($42)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 69 ($45): Oxygen Sensor Heater Monitor Bank 2- Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 69 ($45)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 70 ($46): Oxygen Sensor Heater Monitor Bank 2 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 70 ($46)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.

OBDMID 73 ($49): Oxygen Sensor Heater Monitor Bank 3 - Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 73 ($49)".

- Select the desired "Test-ID".

- Check specified values at idle.





- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure.

- Switch the ignition off.

- End of diagnosis.