Part 2

Diagnostic Modes 01 - 09

Diagnostic Mode 06 - Read Test Results for Specific Diagnostic Functions (Part 2)

OBDMID 74 ($4A): Oxygen Sensor Heater Monitor Bank 3 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 70 ($46)".

- Select the desired "Test-ID".

- Check specified values at idle.

P3218:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID 77 ($4D): Oxygen Sensor Heater Monitor Bank 4 - Sensor 1

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 77 ($4D)".

- Select the desired "Test-ID".

- Check specified values at idle.

P3153:

- If any component or system fails to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID 78 ($4E): Oxygen Sensor Heater Monitor Bank 4 - Sensor 2

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 78 ($4E)".

- Select the desired "Test-ID".

- Check specified values at idle.

P3248:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID $71 (113): Secondary Air Injection (AIR) System 1 (Bank 1)

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 71 ($113)".

- Select the desired "Test-ID".

- Check specified values at idle.

P0491:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID $72 (114): Secondary Air Injection (AIR) System 2 (Bank 2)

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 72 ($114)".

- Select the desired "Test-ID".

- Check specified values at idle.

P0492:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID $73 (115): Secondary Air Injection (AIR) System 3 (Bank 3)

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 115 ($73)".

- Select the desired "Test-ID".

- Check specified values at idle.

P1497:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID $74 (116): Secondary Air Injection (AIR) System 4 (Bank 4)

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 116 ($74)".

- Select the desired "Test-ID".

- Check specified values at idle.

P1498:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID 162 ($A2): Mis-Fire Cylinder 1 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 162 ($A2)".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.

P0301:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID 163 ($A3): Mis-Fire Cylinder 2 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 163 ($A3)".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.

P0302:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID 164 ($A4): Mis-Fire Cylinder 3 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 164 ($A4)".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.

P0303:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID 165 ($A5): Mis-Fire Cylinder 4 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 165 ($A5)".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.

P0304:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID 166 ($A6): Mis-Fire Cylinder 5 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 166 ($A6)".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.

P0305:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID 167 ($A7): Mis-Fire Cylinder 6 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 167 ($A7)".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.

P0306:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

OBDMID 168 ($A8): Mis-Fire Cylinder 7 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "OBDMID 168 ($A8)".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.

P0307:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

Test-ID 169 ($A9): Mis-Fire Cylinder 8 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 169 ($A9)".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.

P0308:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

Test-ID 170 ($AA): Mis-Fire Cylinder 9 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 170 ($AA)".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.

P0309:

- If any of the components or systems fail to meet the specified values, refer to Diagnostic "Mode 03: Interrogating Fault Memory" to check for stored DTC's or the corresponding diagnostic repair procedure. Diagnostic Mode 03 - Read DTC Memory

- Switch the ignition off.

- End of diagnosis.

Test-ID 171 ($AB): Mis-Fire Cylinder 10 Data

- Connect the scan tool.

- Start the engine and let run at idle speed.

- Select "Mode 6: Check test the results of components that are not continuously monitored".

Select "Test-ID 171 ($AB)".

- Select the desired "Test-ID (TID)" or "Hex-ID".

- Check specified values at idle.