Backrest Cover and Cushion
Backrest Cover and Cushion
1 Backrest Cover
Removing
- Remove seat. Refer to => [ Seat ] Front RS Sport Seat.
- Remove the backrest. Refer to => [ Front Backrest and Seat Pan ] Front RS Sport Seat.
- Remove both outer parts of belt guide. Refer to => [ Outer Part of Belt Guide, Removing and Installing ] Front RS Sport Seat.
- Pry out cover on belt guide, drill out pop rivet with a dia. 5.0 mm drill and remove belt guide. Refer to => [ Belt Guide, Removing and Installing ].
- Pry grip channel at edge of backrest cover - 1 - all around out of guide at backrest - 6 -. Refer to => [ Pry grip channel for backrest cover out of guide ].
- in bending sections, grip channel is also secured using retaining clamps - 3 -, carefully remove retaining clamps.
- Carefully loosen seams of backrest cover from Velcro fastener at backrest cushion - 4 -.
- Disengage lower retaining strip at pneumatic block - 5 -.
- Remove backrest cover.
Installing
To install, perform the steps used in removal in reverse order.
2 Outer Part of Belt Guide
• Removing and Installing, refer to => [ Outer Part of Belt Guide, Removing and Installing ] Front RS Sport Seat
3 Retaining Clamps (Qty. 8)
• For grip channel of backrest cover
• Install in bend in backrest
4 Backrest Padding
Removing
- Remove backrest cover - 1 -.
- Disengage flaps for backrest bolster inflation adjustment - 7 - at retaining bracket of backrest, refer to => [ Disengaging flap for backrest bolster inflation adjustment ].
- Disconnect pneumatic hose to backrest bolster inflation adjustment.
- Remove backrest cushion from backrest.
Installing
To install, perform the steps used in removal in reverse order.
5 Pneumatic Block
Removing
- Remove backrest cover - 1 -.
- Remove backrest cushion - 4 -.
- Carefully loosen bonding of pneumatic block from backrest.
- Swing pneumatic block toward front at upper edge.
- Free up electrical wiring harness.
- Remove pneumatic block.
Installing
To install, perform the steps used in removal in reverse order.
- If necessary, replace double adhesive tape.
• Assignment of pneumatic block. Refer to => [ Pneumatic Block Component Assignment ] Front RS Sport Seat
6 Backrest
• Removing and Installing, refer to => [ Front Backrest and Seat Pan ] Front RS Sport Seat
7 Belt guide
• Removing and Installing, refer to => [ Belt Guide, Removing and Installing ]
8 Trim
• for belt guide
• Removing and Installing, refer to => [ Belt Guide, Removing and Installing ]
9 Pop rivet
10 Flap for backrest bolster inflation adjustment
• Disengage. Refer to => [ Disengaging flap for backrest bolster inflation
adjustment ]
Belt Guide, Removing and Installing
- Pry out trim - 1 - with Pry Lever (80 - 200) at outer corner - arrow A -.
- Remove trim downward - arrow B -.
- Drill out pop rivets - arrows - with a dia. 5.0 mm drill.
- Remove belt guide - 1 - from backrest frame.
Pry grip channel for backrest cover out of guide
- Starting at bottom, pry grip channel for backrest cover out of guide at backrest, using e.g. an awl - arrow -; lightly press together backrest cushion in order to release backrest cover.
Disengaging flap for backrest bolster inflation adjustment
- Swivel backrest bolster inward - arrow A - and disengage flaps - 1 - for backrest bolster inflation adjustment at retaining bracket - 3 - of backrest - arrow B -.
- Disconnect pneumatic hose - 2 - to backrest bolster inflation adjustment.
- Remove backrest cushion from backrest.