Windshield Washer Fluid Reservoir, Vehicles With Auxiliary Heating
Windshield Washer Fluid Reservoir, Vehicles with Auxiliary Heating
Special tools, testers and auxiliary items required
• Drip tray
Removing
- Switch off ignition and remove ignition key.
- Remove right front wheel.
- Remove the noise insulation in the center - attachments 1 through 3 -.
- Remove the noise insulation on the right side - attachments 1 through 3 -.
- Remove the clamps - 1 - and - 5 -.
- Remove the bolt - 6 - on the front exhaust pipe bracket.
- Remove the auxiliary heater front exhaust pipe - 2 -.
- Remove the coolant hose - 4 - bracket - 3 -.
- Remove the right headlamp.
• Halogen Headlamps. Refer to => [ Headlamps ] Halogen Headlamp, Through 05.2008
• HID Headlamps. Refer to => [ Headlamps ] HID Headlamps, Through 05.2008
• Bi-Xenon gas discharge headlamps with cornering lamp. Refer to => [ Headlamps ] Bi-Xenon Gas Discharge Headlamps With Cornering Lamp, Through 05.2008
Vehicles with gasoline engine
- Remove the line - 3 - on the filler tube - 2 - for the windshield washer fluid reservoir to the EVAP canister.
- Remove the EVAP canister, with the lines still connected, upward and out of its mount - arrow - and lay it to the side.
- Remove the screw - 1 - on the windshield washer fluid reservoir filler tube.
Vehicles with TDI engine
- Remove the fuel filter, with the lines still connected, upward and out of its mount - arrow - and lay it to the side.
- Remove the screw - 1 - on the windshield washer fluid reservoir filler tube- 2 -.
All
- Place a drip tray under the windshield washer fluid reservoir.
- Remove the washer fluid lines - 1 - and - 2 - on the windshield washer fluid pump.
- Free up the wiring harness on the locations identified with - 7 - and - 9 - using the pry lever (80-200).
- Open the bracket - 3 - and remove the electric wire.
- Disconnect electrical connectors - 4 to 6 -.
- Remove bolts - 8 - and - 10 -.
- Slide the windshield washer fluid reservoir in the drive direction.
- Unclip the auxiliary heater fuel line - 3 - on the windshield washer fluid reservoir - 1 - and on the filler tube - 4 -.
- Remove the filler tube in - direction of arrow - from the windshield washer fluid reservoir.
- Remove the screw - 2 - on auxiliary heater bracket.
- Remove nuts - 1 - and - 2 -.
- Release the lower auxiliary heater bracket - 3 - on the longitudinal member in - direction of arrow A - and on the side of the longitudinal member in - direction of arrow B -.
- Push the auxiliary heater in the drive direction far enough toward the rear until it is possible to remove the windshield washer fluid reservoir from the guide.
Installing
Install in reverse order of removal, noting the following:
- Make sure that the fuel line edge protection - arrow - on the lock carrier - 1 - and that the wiring harness are not missing.
• Washer fluid hose must engage audibly into connection for washer fluid pump.
- Install the auxiliary heater exhaust pipe.
- Install the right headlamp.
• Halogen Headlamps. Refer to => [ Headlamps ] Halogen Headlamp, Through 05.2008
• HID Headlamps. Refer to => [ Headlamps ] HID Headlamps, Through 05.2008
• Bi-Xenon gas discharge headlamps with cornering lamp. Refer to => [ Headlamps ] Bi-Xenon Gas Discharge Headlamps With Cornering Lamp, Through 05.2008
- Install the right front wheel housing liner.
Tightening Specifications
