Fuel Metering Valve, Checking
Fuel Metering Valve, Checking
The following procedure is used to diagnose the Fuel Metering Valve (N290) which is controlled by Engine Control Module (J623).
Special tools, testers and auxiliary items required
• multimeter.
• Wiring diagram.
Test requirements
• The Engine Component Power Supply Relay (J757) OK.
• The Fuse (SA5) OK.
• The fuel filter OK.
• The parking brake engaged.
• The battery voltage at least 12.5 V.
• The selector lever of automatic transmission in position "P" or "N".
• All electrical consumers switched off.
• A/C switched off.
• The fuel tank at least 1/4 filled.
• The ignition switched off.
Test procedure
- Perform a preliminary check to verify the customers complaint. Refer to => [ Preliminary Check ] Preliminary Check.
Start diagnosis
- Remove three screws - arrows - and the engine lifting eye to gain access to the electrical harness connector.
- Disconnect the Fuel Metering Valve (N290) electrical harness connector - 2 -.
Checking internal resistance
- Using a multimeter , check the Fuel Metering Valve (N290) terminals 1 to 2 for resistance
Specified value: 450 to 1000 ohms.
If the specified value was not obtained:
- Replace the Fuel Metering Valve (N290). Refer to the appropriate service information
If the specified value was obtained:
Checking voltage
Crank the engine.
- Using a multimeter, check the Fuel Metering Valve (N290) electrical harness connector terminal 1 to Ground (GND) for voltage.
Specified value: battery voltage.
- Switch the ignition off.
If the specified value was not obtained:
- Check the wiring from the Fuel Metering Valve (N290) electrical harness connector terminal 1 to the Engine Component Power Supply Relay (J757) socket 8/87 for an open circuit or a short circuit to Ground (GND).
- Check the electrical harness connector for damage, corrosion, loose or broken terminals.
- If necessary, repair the wiring connection.
If no malfunctions are found in the wiring:
Checking wiring connections
If the manufacturers test box is being used, perform the following step.
- Install the test box.
If the manufacturers test box is not being used, perform the following step.
- Remove the Motronic Engine Control Module (ECM) (J623). Refer to appropriate service information.
- Using a multimeter, check the Fuel Metering Valve (N290) electrical harness connector terminal 2 to the Engine Control Module (ECM) (J623) electrical harness connector T60 terminal 60 for resistance.
Specified value: 1.5 ohms Max.
If the specification was not obtained:
- Check the wiring for an open circuit, a short circuit to each other, Battery (+) or Ground (GND).
- If necessary, repair the faulty wiring connection.
If no malfunction is detected in the wiring:
- Erase the DTC memory. Refer to => [ Diagnostic Mode 04 - Erase DTC Memory ] Diagnostic Modes 01 - 0A.
- Perform a road test to verify repair.
If the DTC does not return:
Repair complete, Generate readiness code. Refer to => [ Readiness Code ] Monitors, Trips, Drive Cycles and Readiness Codes.
- End diagnosis.
If the DTC returns and no malfunction is found in the wiring and voltage supply was OK:
- Remove the Motronic Engine Control Module (ECM) (J623). Refer to appropriate service information.
Assembly is performed in the reverse order of the removal, note the following:
Final procedures
After repair work, the following work steps must be performed in the following sequence:
1. Check the DTC memory. Refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Modes 01 - 0A.
2. If necessary, erase the DTC memory. Refer to => [ Diagnostic Mode 04 - Erase DTC Memory ] Diagnostic Modes 01 - 0A.
3. If the DTC memory was erased, generate readiness code. Refer to => [ Readiness Code ] Monitors, Trips, Drive Cycles and Readiness Codes.