Instrument Panel Assembly Overview
Instrument Panel Assembly Overview
1 Instrument Panel
• Follow all safety precautions when working on pyrotechnic components. Refer to => [ Restraint System Components, Safety Precautions and Testing Procedures ] Description and Operation.
• Follow the allocation of the airbag to the instrument panel => Parts Catalog.
• Removing and Installing, refer to => [ Instrument Panel ] Instrument Panel
2 Center speaker trim
• Removing and Installing, refer to => [ Center Speaker Trim ] Center Speaker Trim
• First, insert in the front of the instrument panel and press on it until it engages audibly.
3 Treble speaker
• Quantity: 2
• If equipped
4 Side speaker trim
• Quantity: 2
• Removing and Installing, refer to => [ Side Speaker Trim ] Side Speaker Trim
• First, insert in the front of the instrument panel and press on it until it engages audibly.
5 Top front defroster vent
• Removing and Installing, refer to => [ Upper Front Defroster Vent ] Upper Front Defroster Vent
• Set defroster vent in place and feed harness connector for sunlight photo sensor (G107) through the opening.
• Press on it until it clicks into place
6 Sunlight photo sensor (G107)
7 Bolt
• 3 Nm
8 Upper Cover
• For the instrument panel
• Removing and Installing, refer to => [ Instrument Panel Upper Cover ] Instrument Panel Upper Cover
9 Bolt
• Quantity: 6
• 3 Nm
10 Trim Strip
• For the instrument panel cover
• Removing and Installing, refer to => [ Instrument Panel Cover Trim Molding ] Instrument Panel Cover Trim Molding
11 Bolt
• Quantity: 14
• 3 Nm
• Tightening sequence refer to Instrument Panel Cover Trim Molding
12 Bolt
• Quantity: 5
• 3 Nm
13 Top rear defroster vent
• Removing and Installing, refer to => [ Upper Rear Defroster Vent ] Upper Rear Defroster Vent
14 Mid-Range Speaker
• If equipped
15 Side Cover
• For the instrument panel
• Removing and Installing, refer to => [ Instrument Panel Side Cover ] Instrument Panel Side Cover
• Press on it until it clicks into place
16 Front passenger airbag with front passenger airbag igniter 1 (N131) and front passenger airbag drain valve igniter (N491)
• For countries with front passenger airbag igniter 2 (N132)
• Follow all safety precautions when working on pyrotechnic components. Refer to => [ Restraint System Components, Safety Precautions and Testing Procedures ] Description and Operation.
• Follow the allocation of the airbag to the instrument panel. Refer to Parts Catalog.
• Assembly Overview => [ Front Passenger Airbag ] Front Passenger Airbag
• Removing and Installing, refer to => [ Front Passenger Airbag Igniter N131/N132/N491 ] Front Passenger Airbag Igniter N131/N132/N491
1 Left instrument panel vent illumination bulb (L67)
2 Instrument panel vent
• For driver side
• Removing and Installing, refer to => [ Driver Side Instrument Panel Vent ] Driver Side Instrument Panel Vent
• Replace any damaged or deformed clips.
• When sliding it into the installation opening, make sure the air duct engages correctly.
• Press it into the installation opening as far as the stop.
3 Bolt
• 1.5 Nm
4 Trim panel
• Removing and Installing, refer to => [ Driver Side Instrument Panel Vent ] Driver Side Instrument Panel Vent
5 Control buttons for instrument cluster (E493)
6 Instrument Cluster
7 Bolt
• Quantity: 4
• 3 Nm
8 Instrument Panel
• Follow all safety precautions when working on pyrotechnic components. Refer to => [ Restraint System Components, Safety Precautions and Testing Procedures ] Description and Operation.
• Follow the allocation of the airbag to the instrument panel => Parts Catalog.
• Removing and Installing, refer to => [ Instrument Panel ] Instrument Panel
9 Front information display control head (J685)
10 Cover
• For the front information display control head (J685)
• Removing and Installing, refer to => [ Front Information Display Control Head Cover J685 ] Front Information Display Control Head Cover J685
• Replace any damaged or deformed clips.
• when the gap dimensions are even, pay special attention to the right and left sides when installing
• Press on it until it clicks into place
11 Bolt
• Quantity: 4
• 1.5 Nm
12 Instrument panel vent
• for front passenger side
• Removing and Installing, refer to => [ Front Passenger and Center Instrument Panel Vent ] Front Passenger and Center Instrument Panel Vent
• Tighten the lower screws first when installing the panel vent illumination on the passenger side, center.
13 Bolt
• Quantity: 3
• 3 Nm
14 Rear cover
• For the instrument panel
• Removing and Installing, refer to => [ Rear Instrument Panel Cover ] Rear Instrument Panel Cover
• Press on it until it clicks into place
15 Bolt
• Quantity: 4
• 3 Nm
16 Bolt
• Quantity: 2
• 3 Nm
17 Right instrument panel vent illumination bulb (L69)
18 Bolt
• Quantity: 2
• 1.5 Nm
19 Trim
• for the instrument panel cover
• Removing and Installing, refer to => [ Instrument Panel Cover Trim ] Instrument Panel Cover Trim
• Press on it until it clicks into place
20 front passenger seat front height adjustment switch (E461)
21 Analog clock (Y)
22 Navigation System
• If equipped
23 Bolt
• Quantity: 2
• 3 Nm
24 Trim
• For navigation system
• Removing and Installing, refer to => [ Navigation System Trim ] Navigation System Trim
• Press on it until it clicks into place
25 Trim
• For the instrument panel
• Removing and Installing, refer to => [ Instrument Panel Trim ] Instrument Panel Trim
26 Bolt
• 3 Nm
27 Instrument panel cover in the center
• Removing and Installing, refer to => [ Instrument Panel Cover ] Instrument Panel Cover
28 Bolt
• 3 Nm
29 Hood
• For navigation system
• Removing and Installing, refer to => [ Navigation System Lid ] Navigation System Lid
30 Access/Start Authorization Switch (E415)
• Trim, Removing and Installing, refer to => [ Access/Start Authorization Switch E415 Trim ] Access/Start Authorization Switch E415 Trim
• Set the upper and lower trim in place on the switch and press on them until they audibly latch.
31 front passenger seat front height adjustment switch (E461)
32 Trim
• For instrument cluster
• Removing and Installing, refer to => [ Instrument Cluster Trim ] Instrument Cluster Trim
• Replace any damaged or deformed clips.
• Replace any trim damaged during removal
• Press on until the clips engage completely in the mounting points