Track Control Arm Mount
Track Control Arm Mount
Special tools, testers and auxiliary items required
• Pressure plate (VW 402)
• Punch (VW 412)
• Subframe support assembling device (3301)
• Subframe support assembling device (3346)
• Subframe support assembling device (T10030)
• Assembly paste
Removing and Installing the Control Arm Mounting (On the Wheel Bearing Housing Side)
• Hold on to the mounting firmly as you remove and install the control arm.
Removing
- Remove the control arm. Refer to => [ Track Control Arm ] Track Control Arm.
- Mark the press-in depth on the mount - 1 - - arrow -.
• Use a waterproof felt-tip pen/marker to make the mark.
- Lay out the special tools as shown in the illustration.
1. (VW 412)
2. Thrust piece (T10030/1)
3. Bearings
4. Control arm
5. Sleeve-press tool (3301/3)
6. Bearing race (3301/1)
7. (VW 402)
- Remove the mount - 3 - from the control arm - 4 -.
Installing
- Transfer the mark you made for the press-in depth from the old to the new mount.
- Apply a thin coat of assembly paste on the mount. Allocation, refer to the Electronic Parts Catalog (ETKA).
- Install the mount - 3 - in the control arm - 4 -.
- Lay out the special tools as shown in the illustration.
1. (VW 412)
2. Thrust piece (T10030/1)
3. Bearings
4. Control arm
5. Thrust piece (3346/1)
6. Bearing race (3301/1)
7. (VW 402)
• Make sure that the mount does not get installed crooked when pressing it in to place.
- Install the mount - 3 - in the control arm - 4 -.
- Pay special attention to the press-in depth mark you made during installation - arrow -.
- Check the press-in depth for the mount - 1 - on the control arm - 2 -.
The - a - and - b - dimensions must be the same.
- If the - a - and - b - dimensions are different, press on the mount some more - 1 -.
- Install the control arm. Refer to => [ Track Control Arm ] Track Control Arm.
Removing and Installing the Control Arm Mounting (On the Subframe Side)
• Hold on to the mounting firmly as you remove and install the control arm.
Removing
- Remove the control arm. Refer to => [ Track Control Arm ] Track Control Arm.
- Mark the press-in depth on the mount - 3 - - arrow -.
• Use a waterproof felt-tip pen/marker to make the mark.
- Lay out the special tools as shown in the illustration.
1. (VW 412)
2. (3346)
3. Bearings
4. Control arm
5. Sleeve-press tool (3301/4)
6. Bearing race (3301/1)
7. (VW 402)
- Remove the mount - 3 - from the control arm - 4 -.
Installing
- Transfer the mark you made for the press-in depth from the old to the new mount.
Bearing Installation Position
- A - = 90° +/- 5°
- Apply a thin coat of assembly paste on the mount. Allocation, refer to the Electronic Parts Catalog (ETKA).
- Install the mount - 1 - in the control arm - 2 -.
- Lay out the special tools as shown in the illustration.
1. (VW 412)
2. (3346)
3. Bearings
4. Control arm
5. Sleeve-press tool (3301/3)
6. Bearing race (3301/1)
7. (VW 402)
• Make sure that the mount does not get installed crooked when pressing it in to place.
- Install the mount - 3 - in the control arm - 4 -.
- Pay special attention to the press-in depth mark you made during installation - arrow -.
- Check the press-in depth for the mount - 1 - on the control arm - 2 -.
The - a - and - b - dimensions must be the same.
- If the - a - and - b - dimensions are different, press on the mount some more - 1 -.
- Install the control arm. Refer to => [ Track Control Arm ] Track Control Arm.