Power Steering Pump, Vehicles With Dynamic Steering
Power Steering Pump, Vehicles with Dynamic Steering
• Always replace seals.
• Do not reuse fluid you have drained.
• Only use hydraulic oil.
1 Bracket
2 Sleeve
• Drive the sleeve back slightly to install the power steering pump.
3 Bolt
• 25 Nm
4 Union Nut
• 38 Nm
5 Pressure Line
• Insert the pressure line completely when installing.
• Observe installation position: The angle between the line connection and power steering pump axle is approximately 72°
6 Seal
• Always replace if removed.
7 Intake Hose
• The marking "P" on the suction hose - arrow - must align with the formed seam - arrow - on the power steering pump.
8 Clamp
• Tension using hose clamp pliers (V.A.G 1275)
• Always replace if removed.
9 Power Steering Pump
• Allocation, refer to the Parts Catalog
• fill with hydraulic oil before installation
• Checking delivery pressure, refer to => [ Power Steering Pump Delivery Pressure, Checking ] Testing and Inspection
• Bleed the steering, refer to => [ Steering, Bleeding after Replacing ] Service and Repair.
• Check hydraulic fluid level, refer to => [ Power Steering Fluid Level, Checking ] Power Steering Fluid Level, Checking.
• Steering system, checking for leaks, refer to => [ Steering, Checking for Leaks ] Steering, Checking For Leaks
10 Bolt
• 25 Nm
Removing
Special tools, testers and auxiliary items required
• Hose Clamps Up to 25 mm Dia. (3094)
• Hose Clamp Pliers (V.A.G 1275)
• Torque Wrench 5-50 Nm (V.A.G 1331)
• Tool Insert, AF 17 (V.A.G 1331/6)
• Used Oil Collection and Extraction Device (V.A.G 1782)
• Drip Tray for VAS 6100 (VAS 6208)
• Spanner Wrench (3212)
• Engine Bung Set (VAS 6122)
General Information
Vane pump is not designed to be serviced. If there are customer complaints, the cause must be determined using a pressure and leak test. If there is a malfunction, replace the vane pump.
• If power steering fluid is low in reservoir, check steering system for leaks.
• If there are leaks in the area of the line connections, the lines/connections must first be inspected for leaks, tightened as necessary and wiped dry.
• Power steering pump is delivered without oil. Therefore, hydraulic oil must be filled before installation and turned by hand. Otherwise, noises when driving or damage to power steering pump may occur.
- Place the vehicle on a hoist.
- Remove the engine cover upward.
• Identify direction of travel before removing ribbed belt. Reversed direction of travel with a used belt can lead to malfunctions. When installing ribbed belt, make sure it is seated correctly on pulleys.
- Remove the ribbed belt.
- Remove the ribbed belt from the power steering pump belt pulley.
- Extract hydraulic oil from reservoir using (V.A.G 1782).
- Clamp off the suction hose - 1 - and return hose - 2 - using the (3094).
• The (3094) must not be secured on the return hose - 2 - in the check valve area. Otherwise, check valve will be damaged.
• The check valve is located in the return hose - 2 - between the hose clamps - arrows -.
- Remove noise insulation.
- Place the (VAS 6208) under the power steering pump.
- Mark the position of the belt pulley to the hub. Make a marking - arrow -.
• If the power steering pump will be replaced, transfer the marking from the hub on the old pump to the new one.
• Because of space restrictions, it is not possible to see the position of the belt pulley holes to the holes in the hub when installing.
- First loosen the belt pulley bolts (only possible on 2 of the 3 bolts because of restricted space). Use the (3212) as a counter hold tool if necessary.
- Turn the power steering pump belt pulley so that the third bolt can be loosened.
- Remove the bolt and remove the belt pulley.
- Open the hose clamps - arrows - and remove the air guide hose.
Applies to Hot Climate Vehicles
- Disconnect electrical connector - 2 -.
- Remove the bolt - 1 - and move the after-run coolant pump (V51) to the side.
- Carefully cut through the cable ties - 1 - for the wiring harness - 2 - if applicable.
- Remove the clamp - 4 - from the intake hose - 3 -. Remove the suction hose - 3 -.
- Lay several cloths under the power steering pump and pressure line.
- Remove the union nut - 1 - and pull the pressure line out of the power steering pump.
- Seal the power steering pump and line connections using clean sealing plugs.
- Remove the two bolts - 1 - for mounting the power steering pump from the front.
- Drive the sleeve - 2 - for the bolt - 3 - in the bracket back slightly to install the power steering pump.
- Remove the power steering pump.
Installing
Install in reverse order of removal. Note the following:
Tightening specifications, refer to => [ Power Steering Pump, Vehicles with Dynamic Steering ]
• Replace seals and gaskets.
• Before installing the new power steering pump on the intake side, fill the hydraulic oil and install it by hand until oil drains out on the high pressure side.
• Secure all hose connections with new hose clamps, refer to the Parts Catalog.
- Note the installation position of the intake hose on the power steering pump.
- Note the installation dimension of the clamp. Dimension - a - must be 4 mm.
- Turn the hub by hand until oil runs out of the pressure side.
- Insert the power steering pump in the bracket.
• The sleeve - 2 - is driven back slightly.
- First install the front bolts - 1 - (quantity: 3) loosely.
- Then install the rear bolt - 3 - loosely.
- First tighten the bolts - 1 - and then the bolt - 2 -.
- Press the pressure line into the power steering pump as far as the stop. Then tighten the union nut - 1 -.
• When installing the pressure line - 4 - make sure the angle between the line connection and the steering pump axle is approximately 72°.
- Attach the suction hose to the connection and install the new clamp - 3 -.
- Align the marking - arrow - made on the belt pulley to the marking made on the hub.
- Tighten the belt pulley bolts - arrows -.
- Clean oiled places in engine compartment.
Install power steering pump ribbed belt.
- Check power steering fluid level. Refer to => [ Power Steering Fluid Level, Checking ] Power Steering Fluid Level, Checking.
- Bleed the steering. Refer to => [ Steering, Bleeding after Replacing ] Service and Repair.
- Check the steering for leaks. Refer to => [ Steering, Checking for Leaks ] Steering, Checking For Leaks.
- Install noise insulation.
- Install ribbed belt and check alignment of ribbed belt.
• When installing the ribbed belt, ensure it is correctly seated in ribbed belt pulley.
1. Vibration damper
2. Idler pulley
3. Tensioning element for the ribbed belt
4. Generator
5. Power Steering Pump
6. Air Conditioning (A/C) Compressor
- Start the engine and check the ribbed belt travel.