Computers and Control Systems: Technical Service Bulletins

• Customer Interest
  • SRS - Warning Lamp ON/Fault Code 1 Set
    • Overview
    • Procedure
    • Warranty Information:
    • Installation of Zae II Control Module (P/N 65 77 8 369 828)
      • Overview
      • Procedure
  • Differential - Final Drive Oil Leaks
  • Instrument Cluster/EKM - Coding Problems
• By Symptom
  • SRS - Warning Lamp ON/Fault Code 1 Set
    • Overview
    • Procedure
    • Warranty Information:
    • Installation of Zae II Control Module (P/N 65 77 8 369 828)
      • Overview
      • Procedure
  • Differential - Final Drive Oil Leaks
  • Instrument Cluster/EKM - Coding Problems
• All Technical Service Bulletins
  • Computers, Controls - Programming VS Veh. Data Status
  • Compuetrs/Controls - Recommended Diagnostic Procedures
  • Computers - ISTA Diagnosis On Vehicles Prior To E46
  • Computers/Control - Loading/Activation Of Enabling Codes
  • Progman(R) - Programming/Coding/Individualization
    • Overview
    • General_Rules_For_Programming
    • Procedure_A_Module_Replacement
    • Procedure_B_Software_Update
    • Procedure_C_Troubleshooting
      • Index
      • Introduction
      • Section I: Preparing A Progman Session
      • Section II: Progman Session Initialization
      • Section III: Before Programming/Coding
      • Section IV: After Programming Coding
      • Illustrations and Table
    • Procedure_E_Coding
  • Computers/Controls - Custom Configuration
  • Updated MoDic(R) Diagnostic Software - D12.0
  • Updated MoDic(R) Software - P11.0 Programming
    • Overview
    • Program Highlights
    • Flash Programming Features
    • Programming the Control Module
      • Overview
      • 1. Determine Customer Service Measures
      • 2. Exchange Control Module
      • 3. Exchange EPROM
      • 4. Adjustment EWS - DME Vehicles From 1/95
      • 5. Clear Adaptation Values
    • Diskette Contents
    • How to Load V11.0 Software With MODIC Station
    • Label Printing
    • Prerequisites For Programming
    • Parts Information
  • ELO Diagnostic Cable - New Special Tool
  • Special Tools - Electrical Connector Release Tools
  • SRS - Warning Lamp ON/Fault Code 1 Set
    • Overview
    • Procedure
    • Warranty Information:
    • Installation of Zae II Control Module (P/N 65 77 8 369 828)
      • Overview
      • Procedure
  • ECM - EPROM Replacement/Application Chart
  • Undefined MoDic(R) Software
    • Overview
    • How to Load C7.0 Software With the MODIC Station
  • Updated MoDic(R) Software - P8.0 Programming
    • Overview
    • Engine Control Module Flash Programming Features
    • Programming the Control Module
      • Overview
      • 2. "Exchange Control Module"
      • 3. "Exchange EPROM"
      • 4. "Adjustment EWS - DME Vehicles From 1/95"
      • 5. "Clear Adaptation Values"
    • How to Load V8.0 Software With the Modic Station
    • Label Printing
    • Prerequisites For Programming
  • Updated MoDic(R) Software - C9.0 ZCS Coding
    • Overview
    • How to Load C9.0 Software With the MODIC Station
    • Label Printing
  • Updated MoDic(R) Software - P9.0 Programming
    • Overview
    • Flash Programming Features
    • Programming the Control Module
      • Overview
      • 1. "Determine Customer Service Measures"
      • 2. "Exchange Control Module"
      • 3. "Exchange EPROM"
      • 4. "Adjustment EWS - DME Vehicles From 1/95
      • 5. "Clear Adaptation Values"
    • How to Load V9.0 Software With the MODIC Station
    • Label Printing
    • Prerequisites For Programming
  • TIS - Software Update 12/96
    • Overview
    • TIS Loading Instructions For DIS Tester
    • TIS Loading Instructions For EPC/TIS Server
    • Proper Care of CDs
      • Overview
      • CD Return Procedure
  • New Special Tool - MoDic(R) Replacement Cable
  • Service/Warranty Coverage - Information Booklet
  • Differential - Final Drive Oil Leaks
  • Emissions - On-Board Diagnostic Code Updated List
  • ECM - DME M5.2 Control Modules
  • EPROM - Replacement/Application Chart Order Form
  • Special Tools - Simulator Tool For Bosch Oxygen Sensors
    • Overview
    • Individual Parts of the Simulator
    • Operator Control/ Panel of Simulator
    • Connecting the Simulator
    • Test 1: Oxygen Sensor Testing
    • Test 2: Oxygen Sensor Voltage
    • Test 3: Simulation of Probe Voltage
  • Tools - Seal Pliers For Speedometer Sender
  • Instrument Cluster/EKM - Coding Problems